Having problems with your 1995 Ford Ranger Supercab ?

Both codes at the same time p0135 and p0145 code on a ford ranger 1995

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 1995 Ford Ranger Supercab

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Both codes at the same time p0135 and p0145 code on a ford ranger 1995


... 1995 Ford Ranger Supercab

I have a '99 Ford Ranger 3.0L that won't start reliably(3 times in 2 weeks).When I turn the ignition to "on",the theft light flashes rapidly,and will eventually give me a 1:6 code(faulty link between PATS module and EECV).I tried a regular door key in the ignition,and a 1:3 code flashed(key code not received)which tells me the transceiver is working properly.When it will start,the theft light works properly and proves out.The truck will start sometimes and runs fine,which makes me discount coil


When the anti-theft light is flashing rapidly then either it is not seeing the key,or the transciever module is not communicating with the PCM. It could be the transciever or it could be the PCM is not powering up for some reason. I would first try r ... 1999 Mercury Cougar

2002 ford ranger 4x4 super cab air bag code and how to reset it replaced air bags and module under console light flashes 4 times and then 6 times what does this mean and how do i reset so light goes out


Think it might be a dealer only job ,most vehicles have a double standard in the software ,so something thats security or safety is encrypted . ... 2000 Ford Ranger SuperCab

2003 ford ranger airbag light is flashing code (46) it flashes 4 times short pause then 6 times long pause


46--- Driver Pretensioner Circuit Resistance HighThat means the buckle in you driver side seat belt system has failed. It has an explosive device called a pretensioner in it which is designed to pull you into place microseconds before th ... 2003 Ford Ranger Regular Cab

94 ford ranger 3 0 timing gear settings 4whd 6cyl


... Cars & Trucks

I have a 1999 Ford Ranger 2.5L 2WD. The check engine light is on and displaying 5 codes when I scan it. P1506 (IAC overspeed error), P0135 (O2 bank 1 sensor 1), P1451 (Evap), P0141 (O2 bank 1 sensor


... 1999 Ford Ranger SuperCab

I have a 2002 ford ranger that got a lot of water in the gas. I have drained the tank and added heat as well as replaced the filter. When I try to start it the battery gauge goes down to 0 and all I hear is the starter clicking. I have checked the battery, starter, and the altinator and all are good. I have gotten it started a couple of times and it idols fine but if I drive it I only get about a mile before it dies and the battery will not turn over the starter. The volt gauge still goes down


... 2002 Ford Ranger Regular Cab

89 ford ranger 2.3L distribtorless EFI...have three relays located directly under the high current fuse box under the hood(passenger side fenderwell)no description on there function,the plugs are color coded can anyoneone help me,one is green,one tan(brown)one grey. I am getting no fire,just replaced ignition module,all fuses are good,it not timing belt,i'm thinking relay or EECIV box.......nothing in owners manuel about these relays!!!!


... 1987 Ford Ranger

2001 ford ranger 4 0 engine timing chain


... Cars & Trucks

HI, I have a 1988 Ford Ranger, V-6, 2.9L. I've had problems with the engine stalling on an intermittent basis. The first time it happened was when I switched on the cruise but it has happened since with or without the cruise on. I recently checked the trouble codes and got a 74 indicating a brake on/off switch problem. I replaced the BOO switch and then noticed the cruise and panel lights weren't working. I checked all the fuses and they are OK. (except one fuse, #16, a 20 c.b. fuse which I can'


I solved this problem so I'm posting this to help others. I was getting a code indicating a problem with the BOO switch (brake on/off). C the switch which is located on the brake pedal and continued to have a code 74. I found out that the cruise cont ... 1988 Ford Ranger

Couple of questions on a 1997 4 cyl Ford ranger; engine light stays on all the time. Sometimes its blinking nut mainly just stays lit. In addition the O/D off light comes on to let me know its off for no apparent reason. And last yesterday I checked the "fluids" as its running sluggish and the container that holds the radiator fluid was empty-what caused this? Its been 0-32 degrees out. thank you for your help.


First off, the check engine light. If it's flashing, that indicates the engine is misfiring. You should immediately pull over and shut it off - driving while misfiring can cause serious damage. The fact that it stays lit indicates that you have store ... Ford Ranger

I have a 2002 ford ranger that got a lot of water in the gas. I have drained the tank and added heat as well as replaced the filter. When I try to start it the battery gauge goes down to 0 and all I hear is the starter clicking. I have checked the battery, starter, and the altinator and all are good. I have gotten it started a couple of times and it idols fine but if I drive it I only get about a mile before it dies and the battery will not turn over the starter. The volt gauge still goes down


I think your on the right path with your shorting thought. Is the distance you can travel always different or always the same? If it is always the same then it may not be a short or how long can it sit and idle when you get it running? ... Cars & Trucks

1999 ford ranger 3.0L, p0303 code reading. Skips alot but not 100% of the time. Replaced plugs, wires ,coil pack and injecter. Attached noid and it fires ok. Stumble gets worse as it warms up, but wi


... 1999 Ford Ranger SuperCab

My 1994 ford mustang 3.8 L Automatic starts runs fine at some times then all of a sudden the car will start to get all sluggish. hooked up my scanner and the codes it is reading a P0135 and P0155


... Ford Cars & Trucks

I have 98 ford ranger 2.5 that broke the timing belt; What type of internal engine problems might I be looking at? I replaced the belt and did a compression test and have 0 compression.


Hello gandolfph: My name is Roger and I will help with your question. I have Alldata and Mitchell on demand programs. I looked at both and neither one says this is a interference motor. That is where the valves bend if the belt breaks. I would go bac ... 1998 Ford Ranger SuperCab

Plz Ineed help ,my car have code P0135 ford ranger 1998 v6 4.0


... 1998 Ford Ranger SuperCab

1994 ford ranger 4x4 4,0 it idles good but when going down road the check engine light comes on within 20 seconds acts like it is flooding out loses power let off for a second and then runs good for couple mile but at any time if you put throttle to floor within lastinch or so same reaction any ideas


It should have a code stored. Some places still carry the scanners for OBD 1 Fords for around fifty bucks. Without knowing anything else about the truck or what codes you have, it sounds like you have a bad throttle position sensor. ... 1994 Ford Ranger Supercab

94' Ford Ranger 2.3L Manual Codes pointed to the DPFE sensor replaced it 4 times now still get the DPFE either voltage to high or Sensor bad


... Cars & Trucks

I have two codes po141 and p0135 on a 1995 ford ranger I put a new o2 sensor on bank one but there is no change, then I swichted the 02 sensors but it's the same thing what else could I do


... 1995 Ford Ranger Supercab

Hi, i have problem for inspection in my car ford ranger 1998 v6 4.0 the problen is codes p1132,p0174,p0135,p0136 and p1151 plz i need help tankyu


... 1998 Ford Ranger SuperCab

"I've entered wrong ford ranger 6500r radio code 13 times & is now locked, what must i do, please help with steps"


... Cars & Trucks

1998 ford ranger obd code cam sensor miss fire monitor bought a a used motor 97 last year the assembly and sensor were missing so we used the one from old motor witch worked fine but now it is time to smog the mil lite stays on. It won't pass replaced sensor useing tool for assembly no change


Please get a brand new sensor.New parts are better than used/ old parts.Visit www.repairpal.com (for estimates)Visit http://www.autopartswarehouse.com/ (for genuine parts)Good luck and remember to rate ... Ford Ranger

FORD RANGER WL TIMING SPROKIT TIMING - 2000 Ford Ranger SuperCab


... 2000 Ford Ranger SuperCab

1991 ford ranger timing marks how to time it - 1996 Ford Ranger SuperCab


... 1996 Ford Ranger SuperCab

Code 54 and code 14 for 89 ford ranger - 1989 Ford Ranger


... 1989 Ford Ranger
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.3518 seconds