Having problems with your 1995 Eagle Vision ?

My 1995 eagle vision problem:the transmission locks when you shift down and it kills the motor?

\015 Is it the transmission or the torque converter?\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

I am not sure if that trans mission is cotrolled by its own computer if it is mabe that is your oproblem or the transmoission itself.
Repair Help & Product Troubleshooting for 1995 Eagle Vision

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My 1995 eagle vision problem:the transmission locks when you shift down and it kills the motor?


I am not sure if that trans mission is cotrolled by its own computer if it is mabe that is your oproblem or the transmoission itself. ... 1995 Eagle Vision

93 Chevy Pick-up,my son put washers between the torque converter and flywheel so the starter would engage. Driving down the road the trans locked up and killed the engine. He tried starting it again the motor would not turn over, after the third try something popped and the motor started-would not go into any gear. I replaced the torque converter but the trans would not pump fluid and would not shift. Fluid did come out the top port of the trans. What kind of problems can I expect from the pres


Yep damage is done that much pressure on the pump will for sure cause problems . the torque should be able to slide a bit anyways as long as the 2 teeth line up in the pump to turn it and it's on the splines inside it, there's clutch pack's inside th ... 1993 Chevrolet K1500

I have a 1986 pontiac parisienne and the transmisiion acts ups ONLY once the motor gets hot, when I come to a stop the car kinda jerks and stutters and if i stio real suddenly it kills the motor what is wrong? It acts fine and shifts great when its cold and only acts up once i drive for a while. Thanx


Soulds like you have a tork converter thats locking up..you can unhook the wires to the tork converter...this is stop it from locking in...the trans will still shift...it just wont have the lockup converter working..its supposed to save fuel...but i ... 1986 Pontiac Parisienne

I have a 5-speed manual shift 1994 Eagle Talon with a non-turbo 16v 2.0 Mitsubishi motor. It idles fine,will rev up to 6-7grand in neutral with no problem,but when you try to shift through the gears, it starts jerking real bad at about 2500-3000 rpm. I've replaced the fuel filte rand plugs, whats up?


3 possible causes, all related to the injection/admission system:\012\012\012 1. the fuel pressure is low so not enough fuel reaches the injectors. You will have to check the pump (in a car of this age advanced wear is to be expected) and the ... 1990 Eagle Talon

I have a 94 s-10 4x4 with a 4l60e I swapped the motor. now the transmission shifts very quickly from first to forth and then to lockup and about kills engine . its also sitting an egr code 32 I have checked the power to transmission and it is ok the transmission worked perfect until the motor swap


The engine was not a match from the same building codes as yours. computerized engine swaps must be exact swaps or problems will arise such as yours ... 1993 Chevrolet S-10

Clutch/spring Hi, Recently I have broken one of the springs from the clutch pedal.I was on a incline put the car in 1st kill the motor and put the emergency brake on and the broken spring came from underneath the dash.I look at it and realize it was a spring from the clutch pedal and it probably wasnt going to be a big deal to change or fix the spring.The clutch still works fine and shifts smoothly.I took it to my local mechanic and he says they have to replace the whole clutch assemby under the


Hi,To my knowledge, the spring is merely to assist the pedal to return at its default position (clutch engaged), that is pedal up. Normally, it would have an exaggerated j ends. The ends are meant to hook to two (2) slots, o ... 2005 Mazda 3

On cold mornings my 2006 f15o makes a rubbing / friction noise up front, when you shift from 2H to 4H it stops . you can coast in neutral it doesn't stop, you kill the motor it doesn't stop, but when taken out of 2 H it stops


It sounds like it's something in the front differential or possibly the transfer case. Is oil level up on both, does the oil look milky like there is water in it. That truck doesn't have manual or automatic hubs does it? If it did I would say it's th ... 2005 Ford F-150

I have a 1991 jeep wrangler yj i put a newnp231 transfer case in it an abrand new shift motor with good vacume lines i have the linkage adusted right but it will not engage in 4wheel drive i dd engageit by removin the shift motor and slid the shift ring in to the 4 wheel position with my fingers and every thing worked i put a vacmpump on the shift motor andit checkedout great i amhavin a hell of a time figuring out why this isnt working any solutions


New Axle grease on the sliding link gear? Change the gear oil in your front differential, and, make sure the vacuum line is the correct I.D. If it is too large (it doesn't take but 1mm or 2mm - 3/16" or 7/32"?) and the vacuum is just a little too wea ... 1991 Jeep Wrangler

My 2000 F250 Superduty is stuck in 4X4. When i take the shift motor off the transfer case i can shift it with a wrench and when i hook a jumper wire to the shift motor it works,but i have no power to the shift motor. Anyone have an idea whats wrong?


They have a control module by the glove box that go bad sometimes ... 2000 Ford F250 Super Duty Crew Cabs

I have a eagle vision 94 esi going down the road about 20 to 40 miles an hour the car has trouble shifting to 3rd gear i believe if i feed it gas slowly it might shift into gear or it shift down causi


You have to repair the motor & trans mounts oranything else-- before diagnosing the trans issues ... 1994 Eagle Vision

'89 Ford Ranger will shift into 4X4 but will not shift out. Can change it to 2wd by hand but the motor will only shift it one way. Its push button shift. New shift motor.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thank You for using FixYa. Kindly follow\015\012the instructions: Put the truck in neutral, have your foot on the brake, switch\015\012 ... 1989 Ford Ranger

I own a 1999 Expedition that I used the 4wd High on 2 dayss ago and never used the 4wd Low at all. As I got home a put it back into AWD and parked it. Two mornings later I climbed into it to take my little girl to school and it was engaged in 4wd low. I couldn't get it out. I have since removed the shift motor and manually shifted it into AWD with no problem. Now the dash lights still show 4wd low and the motor is still in that position. The fuse is good and the switch is good. Could the motor


This is very strange because of How the low range is engaged. I drive a 1999 F150 4x4 which has the same dash and controls for the 4x4 as your Expedition. I do know that the fan control switch is unfortunately the same shape and very close to the 4x ... 1999 Ford Expedition

Have a 2005 polaris ranger 500! With the key off it will shift threw all gears fine but when I start it and shift to a gear that's the gear it stays in until I turn motor off. It will not shift threw gears properly with motor running. Pulles are lined up 2 way bearings in Pulles are ok. Thinking this is a idle problem. Any other suggestions?


... Cars & Trucks

99 E250 when motor is running van wont shift out of park when motor is off . when ignition is on and motor not running it will shift just fine


The shift interlock is not releasing. You are doing emergency release procedure with engine off and key in off position.\012Likely you don't have brake lights either. When you step on the brake with the key ON, it releases the shift lock solen ... Ford E-Series Van

I have a 2003 Kia Sorento (automatic) that will not shift from 3rd to 4th at about 45 mph. They have changed out the shift motor and they are still getting a code that the Transfer case shift motor is bad. My mechanic is not able to figure it out the issue. . . any suggestions????


... 2003 Kia Sorento

Hillo my name is victor i have a 2001 concorde and im having troble with tran it is not shifting properly sometime it shift normal and sometime is stay stuck in 1st gear sometime shift to 2nd and stay there im scare im mite blow motor by raving motor needhelp please


Try checking fluid level, could be bad governer, but more likley clutches or bands ,or drums try to go through gears manualy in these newer cars the valve body is all operated by computers,You will probably need to take it to have it pulled and rebui ... 1999 Chrysler Concorde

We R&R a motor into a 2002 pontiac grand prix-superchaged. motor only starts with a shot of ether and idles high. replaced oxygen sensor with no luck. took it for a test drive and doesnt shift properly. other than the high idle and shift problems the motor appears to run great, ant ideas?


When you switched the motor, did you grab the computer that was with the original motor? You will need it, unless the vins are close to the same. Otherwise you may have computer problems. You may not be getting fuel pump activity, or no fuel regulati ... Pontiac Grand Prix

My 92 wrangler will shift into 4high but not 4 low.It seems to have some air flow at shift motor. Does this mean I need a shift motor?


Yes thats what it sounds like....Cant really be sure. Seems like you know your Jeep go with your first choice. ... 1992 Jeep Wrangler

I need to know if the shift motor wiring runs through the radio harness. The radio was ripped out and now the 4x4 wont shift . I checked the shift motor and it still works fine, just not at the switch.


Is it possible that the switch is not plugged in all the way,? i know this is a stupid question, but you said the radio was ripped out as maybe stolen, now the other day i pulled the radio out of mine as the display stopped illuminating and the s ... 2002 Ford Explorer

Just replaced motor in 87 nissan with 90 motor. Also had to replace clutch slave cylinder. Got good peddle,shifts trough gears just fine,with engine OFF. Can't shift when engine is ON. If I put i


Wow, This is a good question,. I am thinking that you may have the throw out bearing handle connected or a bad pressure plate which is inhibiting the relase of the engagement of the engine to the ******..I hope this helps!Best RegardsCk ... Nissan Cars & Trucks

1999 NBS Z71, transfer case will not shift with push buttons, build code NP8, shifted to 4HI got a SERVICE 4WD light but went away and the truck completed the shift to 4HI. When I went to shift back to 2HI it would not shift, it would shift 4HI to Auto 4WD. Have changed the selector switch in the dash, repair shop told me the transfer case actuator motor was bad, I changed that- now the TC will not shift out of NEUTRAL. The TC feels fine when shifting with wrench- Question: how many positions


... 2005 Chevrolet Silverado

2001 f250 won't shift into 4wd high using the dash panel button. can manually lock hubs. how do i diagnose whether the transfer case shift motor is actually getting power, or if the motor itself is defective and needs to be replaced.


You can use a test light to see if you are getting power to your shift actuator by unplugging actuator and testing for power at your wires while someone activates your switch,if you have power then should be a bad actuator. ... 1999 Ford F250 Regular Cab

I have a 1990 f 150 with a 5.0 ltr. 5 speed manual trans. And the motor will rev up to 3000 rpms when I. Up shift and stay there. I have to hold the clutch and turn off the motor and restart the engine for the rpms to come back down. This is a random problem, that happens 2 or 3 time a day when I have to shift the trans. I drive the truck about 30 miles at a time to work.


... 1990 Ford F150

I just installed my transmission and it is like there is no slippage to it it is staying fully ingaged if i put my foot on thebrake it kills the motor un less i have the rear wheels jacked up i cant even put it in drive it kills the motor


I can only assume its a manual transmission. Sounds like the clutch isn`t installed correctly, and staying engaged. Recheck the throw out bearing is engaged in the forks correctly, sounds like its not disengaging the clutch. If its an auto then sound ... Chevrolet Camaro

1996 Saturn SC1 manual transaxle. with clutch pedal up and motor running can shift through all the grears. I was driving, pushed in the clutch pedal and down shifted from 3rd to 2nd as making a turn when I released the clutch pedal there was nothing there the motor just reved up like it was still in nuteral.


Time has come to pay someone to pull the motor out and replace the clutch, do all the clutch components and resurface the flywheel. If the pedal is up then you do not have an actuator/hydraulic failure, your problem lies within the bellhousing. do so ... 1996 Saturn SC
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.4878 seconds