Having problems with your 1995 Chevrolet Suburban ?

How to remove wheel hub from 1995 chev suburban

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 1995 Chevrolet Suburban

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to remove wheel hub from 1995 chev suburban


... 1995 Chevrolet Suburban

I need to replace front wheel bearings on a 1982 Chev Silverado 4X4 with manual Warn hubs. It looks like I need to take a solid ring off of the spline (tough to do) and pull the stud disk off the rotor. I have removed the calipers. Any suggestions on the tools required?


... 1983 Chevrolet Silverado

I need to replace a wheel stud and the brake disks on my 1992 Landcruiser LJ78. It has electric hubs. Now, I can easily remove the lid of the hub, but the electric hub is fixed with fout nuts and even though I release them, I am unable to remove it, probably because there are conic ''washers'' that t are stuck in the wholes underneath. Do I need at all to remove this in order to get to the wheel nut or is there another way? Many thanks Manfred


You will first be removing the hub plate with your 10mm socket. \015\012Next you will take your 12mm socket and loosen all the nuts all the way to the end of the studs but do not remove the nuts all the way just yet. \015\012You will take ... 1992 Toyota Land Cruiser

I was going to replace a wheel brake cylinder on my rear axel. I thought I could just pull off the hub to get to the brake assembly but there is a bolted on cap and screwed on plate on the end of the axel. It looks like I have to unscrew the plate &/or then remove the nuts on the end of the axel. ??Will I need to remove the axel to get the hub off, or does this just hold the wheel hub onto the axel and brake assembly??


Some cars/trucks have the hub mounted with screws/bolts. You will have to remove them to get the hub off. You may need a rubber mallet to beat on the hub a little to get it to come off past the groove the brake pads may have made in the hub. After yo ... Dodge Ram 2500

CV replacement I am about to replace both CV joints 1999 Pulsar. Do I remove the hub to free the outer shaft or pull the shaft inward from the wheel hub. Removing the hub I suspect a suspension spring issue. Does one need to use a spring arrester to hold pressure up or will the CV shaft clear the hub removing the lower trunion only. Thx, John


You don't have to pull the hub! No spring compressor needed. Either unhook the steering knuckle from the strut or thre lower ball joint and swing it out away from the car. Remeber to remove the brake calipers and tie rod ends to get more "swing". It ... 1990 Nissan Pulsar

2001 Buick Regal wheel bearing removal problem. Got the 4 hub bolts removed but the hub won't budge. Does the parking brake piston also need to be removed or do I just hit the hub harder? Any directions on removing the parking brake mechanism?


See if your local AutoZone has a hub puller that you can rent/borrow. Yes, if they dont have one, you will need to hit it from the inside to the outside. They like to corrode in the axle housing and sometimes are a real pain in coming out. Note; when ... 2001 Buick Regal

Need to replace front wheel bearing. Already removed wheels, caliper, rotor, hub, and axle nut. Next step(s)? The darn bearing was so bad it practically fell out once I removed the hub.


The complete Knuckle has to be removed from the car. The bearing is pressed out and in. If you dont have a press, you will have to take it to an auto parts store with a machine shop. The bearing is siezed and you cannot bang it out. I have been the ... 2001 Ford Focus

I removed the cap assembly,I also removed snapring from the end of the axle. The body assembly still will not slide out of the wheel hub. How do I get the body assembly out of the wheel hub


Keep pulling. it comes out. ... 1990 Ford F250

Cannot get the hub off to replace rotors on the 2004 chevrolet colorado the rotors are behind the wheel hub need to remove hub to replace the rotors is there someway to remove the hub


The rotors should be on the hub behind the wheel... you will have to remove the brake caliper and it should just pull off... may be a few clips on the wheel stud ... 2004 Chevrolet Colorado

How do you remove the Hub and Rotor on a 97' F250 with Auto 4 wheel drive? I can not get the rotor to come off. I know that the hub must come with it. However, I am not sure what I have not removed in order to free up the hub.


Section 05-03C: Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive\015\012\015\0121997 F-250/350/Super Duty Workshop Manual\015\012\015\012\015\012REMOVAL AND INSTALLATION\015\012\015\012Procedure revision date: 05/17/2000\015\012\015\012\015\012Lo ... 1997 Ford F250 SuperCab

I need to remove the front brake rotors from my 94 Isuzu trooper to either turn or replace them. Is this a complex project requiring special tools to remove or re-install due to the auto 4wd hubs? I have removed, re-packed and replaced rear wheel bearings before, but never fronts or messed with 4wd hubs.


... Isuzu Trooper

I removed lug nuts from rear wheel on 2006 ram 1500 but wheel is ''stuck'' and cannot be pulled from axle. There is a center ''hub'' on rear but not on front wheel. Can't determine if this ''hub'' should be taken off first; seems to be rusted in place.


Spray some penetrating oil around hub opening, then tap aroung hub with a hammer, it will eventually come off, You are right, it is rusted in place ... 2006 Dodge Ram 1500

I have just purchased a replacement hub for my 2003 Ram 1500. There are no instructions on how to remove & replace the hub. The Ram has ABS. I"m also going to replace the front brake pads on both front wheels. I know how to replace the pads but I'm wondering if I need special tools for removal of the Hub.


The best way for me to walk you through this is to have you watch a video because it's a lot of typing and might not make much sense if you were reading it. Check it out here: ... Dodge Ram 1500

I am unable to remove the wheel hub. I am trying to replace the wheel bearing. The car is an Esteem 1.8 driver's side wheel hub. Any tips or suggestions appreciated.


This is ussualy pressed in with a press. if you really have to. beat the old one out put the new one in the freezer and place the recieving part in a hot spot. i have found a propane grill works well at its highest setting. what this does is shrink t ... 2001 Suzuki Esteem

89 Jeep Comanche needs front wheel bearings. Removed wheel, caliper, but cant remove rotor. Am I missing something or is the rust still holding on? It looks like it has teeth around spindle. Do I need to remove the hub as well? I am also trying to reach the u (joint driver's) side.


4x4, correct? Put the nut back on the axle and run it flush with the end, then give it a smack with a hammer to get the axle splines free.The rotor itself is separate from the hub ...spray with wd40 or other solvent and squirt some where the lu ... 1989 Jeep Comanche

How do I replace a front wheel bearing hub assembl in a 2007 toyota tacoma 4 wheel drive?Does the bearing need pressed onto hub and what size socket needed to remove hub?any thing else I might need to know to do this job myself


... 2007 Toyota Tacoma

Hyundai excel x3 front wheel bearings hub stuck on cant remove how do i get the hub off in order to replace the wheel bearings


Soak good with wd40 first then use a short piece of wood and a hammer to belt them off careful not to hit the axle with the hammer hope this helps glenn.......... ... Hyundai Excel

Need to replace broken front driver side wheel stud on 04 impala - seems like i have to remove hub to make room to push stud through? can someone confirm? if so, how do i get hub off - is it just a matter of removing the axle nut? I don't have a socket big enough to do that, so don't want to buy one unless i have to :). Also, sure would be nice to find an exploded view digram somwhere which names the various parts! thanks!


In the perfect world you are to remove the hub and bearing assembly and yes you would take the axle nut off,but when you are paid flat rate as a mechanic you must beat factory quoted time to make money,so with that said,remove the wheel after c ... 2004 Chevrolet Impala

Replacing front wheel hub. drivers side. what size is the socket needed for hub nut? also, How to remove abs electrical wiring that goes through the wheel well?


... 2002 Jeep Liberty

Removing wheel studs from a 1996 Chevy Cavalier, there is NO hole on the back side of the hub were I can pull the bad stud out. I am Down to removing hub, and cant get it off. not sure what to do...


Take the hub assembly to a machine shop and have the hub pressed off and replace the studs, sorry no short cuts here im afraid ... Chevrolet Cavalier

I have a 2007 grand caravan front wheel drive that needs a new rear bearing hub assembly. I have removed all except the assembly and it will not budge. Is there anything I can use to remove the hub other than a slide hammer puller?


CHRYSLER WARNED AGAINST NOT USING A SLIDE HAMMER PULLER UNLESS YOU ARE GOING TO REPLACE REAR HUB AND BEARING ASSEMBLY.WHEN REPLACING HUB AND BEARING ASSEMBLY THEY HAS TO BE PRESSED OUT. ... 2007 Dodge Grand Caravan SXT Minivan

I can't get the wheel hub assembly off the axel I have removed the caliber and everything. It is a kia sedona 2002. Why won't the wheel hub come off I can't see any bolts. I think I am doing something wrong but I can't figure out what.


Sometimes it just takes a little coersion. Try tapping on the back of it with a hammer. They can get a little stubborn at times. Good luck! ... 2003 Kia Sedona

How do I remove the manuel locking hubs from my 1990 Ford F250 I removed the snapring from the end of the axle but the body assembly still will not slide out. How do I get the body assembly to slide out of the wheel hub???


If my memory serves me correct, I believe you need a special socket to do that. It's a long diameter round socket with small tabs around it. ... 1990 Ford F250

Lug nut was cross threaded on 1998 mazda protege, front wheel. Lugnut broke. Trying to get the hub off to remove the stem. The center hub nut will not budge. What can I do to get the nut loosened and remove it to get the broken stem off?


The nut is a self locking nut that will come off with a 1/2" impact gun ... Mazda Protege

I don't see how to remove rear hub on my 1996 Ford F150 2 wheel drive truck after removing the wheel.


You will need a special socket to remove the bearing lock nut. ... 1996 Ford F150 Regular Cab
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.9191 seconds