Having problems with your 1994 Honda Accord ?

How to change brake pads on 94aerodeck

\015 How to change brake pads on 94 accord aerodeck\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Front or rear? in front only need to remove the 2 screws of caliper, remove it and compress the caliper piston with a c-clamp put the new pads, caliper and tight the screws. For rear is the same procedure but need a tool for compress the caliper piston, looks like \015\012http://www.chain-auto-tools.com/pics/AMR450L.jpg\015\012and in this page is how to use\015\012need to turn clockwise and press for compress it\015\012http://image.superstreetonline.com/f/9520063/130_22_z+acura_rsx_s_brake_install+compress_piston.jpg
Repair Help & Product Troubleshooting for 1994 Honda Accord

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to change brake pads on 94aerodeck


Front or rear? in front only need to remove the 2 screws of caliper, remove it and compress the caliper piston with a c-clamp put the new pads, caliper and tight the screws. For rear is the same procedure but need a tool for compress the caliper pist ... 1994 Honda Accord

My 2002 Camry makes creaking noise when I lightly step in the brakes. I have changed the brake disks and pads twice. Initially, I had replaced by brake pads and disks with non-OEM sets and the creaking sound would come back every few weeks after I had my mechanic clean them. After a few months, I decided to go to the dealer and changed to a completely new OEM set of disks and pads. They even changed the clips as the previous was loose. And, the problem is now back again after 3days. It sounds li


... Toyota Camry

Brakes I turned in my car to change my brake pads but, after 2 months it needed to be changed again. This time they said I also need a new brake disc. How is it within 2 months I needed to replace the pads and disc when it took me three years to wear down the original brakes? Now again I need to replace both pads and disc. It also makes a knocking sound when the brakes is not engaged. What causes this? Is it something the mechanic did that's not right.


It sounds like the rotor (brake disk) is warped. That would cause the pads to wear much more quickly because the disk "wobbles".\015\012The warped disk can also cause the noise, depending on how bad the warp is.\015\012When most shops ch ... 2004 Mazda 3

My 2002 Cadillac Seville STS has electronic brake pad waer sensors. I had a message on the dash reading "change Brake Pads" So I did. The mechanic said he had to replace 2 sensors. The message is still there. I also intermittantly get the abs, TC and BRAKE light on the dash, then they go off when it says "change brake pads". My question is. Do you think the 2 problems are related? Steve


... 2002 Cadillac Seville

BRAKE PADS I NEED THE INSTRUCTIONS ON CHANGING THE BRAKE PADS ON AN OLDSMOBILE CUTLASS CIERRA S WITHOUT LOSING ANY BRAKE FLUID OR THE STEPS TO CHANGING THE PADS AN BLEEDING THE BRAKES? THANX FRUSTRATED FEMALE WANNA BE MECHANIC


OK Jin, 1st I'd like to know if u know what kind of shape the brake pads are in, are they wearing evenly, (inner and outer, and both wheels) are they grinding metal on metal? If everything is wearing evenly, and u haven't gotten to the point of met ... 1993 Oldsmobile Cutlass Ciera

Emergency brakes 2003 Infiniti G35 Coupe - Brembo Brakes, how to change. Changed the brake pads, but could not remove rotor. Do you have to remove center bearing nut to remove rotor; and how do you change out the emergency brake pads?


... 2003 Infiniti FX35

Brake pads Are changing the rear brake pads the same as changing the front brake pads?


If they are both disc pads then it would be the same but if you have drum brakes at the rear then it would be different.tnx 4 using fixya,drcool ... 2001 Lexus IS 300

My Mercedes s500 showing brake lining wear warning notice and saying visit the workshop. What does that mean? I just changed front brake pad. Also I changed the sensor. But, back brake pads are not changed yet. Please help.


... 2003 Mercedes-Benz S500

Spongy brakes changed master cylinder, new brakes, rotors and calipers and wheel cylinders and still have spongy brakes. Bled at least 6 times, still spongy. Rechecked all fittings. Original problem was a driver side caliper was sticking and with no brake pad left and the rotor was bad. Passenger side also had uneven wear on the pads. Consiquently changed everything on both sides. The only thing not done is the brake booster. Any other suggestions.


So long as the brake booster is working, test it by turning on the engine, press the brake pedal all the way down, then shut off engine keeping your foot on the brake pedal, if the pedal comes up slightly pushing against your foot then the booster IS ... Chevrolet Suburban 1500

While changing the braek pads on my 2000 ford expidition, the passenger side brake fluid line broke. I replaced it immediately and continued installing the new pads. I bleed the brakes but now when the truck is on I have to floor my brakes inorder for them to work whereas prior to changing out the brake line I could press around half way and stop the vehicle.


There is still air in the brake system.Bleeding needs to be done from the wheel furthest from the master cyl. and work to the closest.Hope this helps ... 2000 Ford Expedition

After changing the brake pads my brake pedal goes to the floor. I tried to pump the brake, but it did not seem to work. When I changed the pads I took the bolt out of the brake line to the caliper to release pressure. What is the problem with this? Does it need to build pressure?


You need to check the fluid level is correct and that you have tightend the bolts to the caliper ,you have an air lock in the system by the sound of things you need to find the bleed screw on all four brakes and undo each one starting with the one fu ... 2002 Honda Odyssey

Am I supposed to turn the rotor when changing the pads? Just Replaced front brake pads and truck still brakes unevenly (like there's high and low spots on the rotor). 90k miles on truck I bought with 30 k and this is first pad change (I think).


Yes, you ought to turn the rotor when changing the pads. ... 2002 Toyota Tacoma

Will turning rotors fix a warpage issue? Before a recent brake pad change I noticed a shaking when applying the brakes. It is still somewhat noticeable after the brake pad were changed.


Well if they did a brake job at a shop they most likely turned the rotors, turning them if done right should fix it but, do not forget if they are to then below specifications it can cause it as well. I would check the price on new ones that is the b ... 1998 Pontiac Grand Prix

My jaguar xf is only one year old with 20,000 miles. my dealer says I need brake pads. I never had to change brake pads after only 20,000 miles. What kind of brake pads are these? and is this normal? can I upgrade to better brake pads?


... 2009 Jaguar XF

TRYING TO CHANGE MY FRONT BRAKE PADS ON MY GS300 LEXUS 1993. MY QUESTION IS WHEN I TAKE RIM OFF AND LOOSEN UP THE CALIPER TO RELEASE BRAKE PADS AFTER RE-INSTALLING I SHOULDN'T HAVE TO BLEED THE BRAKES LIKE BACK IN THE DAYS. CURRENTLY MY CAR BRAKE PADDLE IS LIKE IT HAS AIR IN IT. SO IF THERE IS ANY DIRECTION YOU CAN GIVE ME IN REPLACING MY FRONT BRAKE PADS I WOULD APPRECIATE IT VERY MUCH


Frank, you are correct, as long as you don't disconnect a brake line at the caliper, or somewhere else, you shouldn't have to bleed the brakes. HOWEVER, you seem to have other issues with the brakes, besides just replacing the pads. Is the master c ... 1994 Lexus GS 300

I changed the front brake pads on my 1989 honda prelude and now they squeak constantly. I took the wheel and calipers back off and looked at the rotor. It had a shiny place on the edge. In the caliper, the thin metal spring holder for the brake pads had a corresponding shiny place. I took the brake pads out and put them back in, making sure that the spring holder did not stick out into the caliper. When we drove, it did not squeak, but the first time we hit the brake, the squeaking started


Did you grease the BACKS of the pads? ... 1989 Honda Prelude

Brakes Can anyone help with my 03 passat. Just got my brake pads repaired and brake disc's. Sine I got the brake pads repaired the ABS light and brake light is coming on more. There was also a new noise developed, a knocking noise when pressing the brake. I also noticed that when I go over bad area of road there is now a rattling at the rear passenger side wheel area. It feels like somthing is under the car and is rattling. So a couple of days later then I got the brake discs changed and it look


On the rattle buy a tube of RTV silicone take your pads off an\015\012coat the back of each pad with the silcone( where the cylinder pushes the pad against the rotor. this will hold the pads in place and the rattle will stop!! ... 2003 Volkswagen Passat

Brakes Can anyone help with my 03 passat. Just got my brake pads repaired and brake disc's. Sine I got the brake pads repaired the ABS light and brake light is coming on more. There was also a new noise developed, a knocking noise when pressing the brake. I also noticed that when I go over bad area of road there is now a rattling at the rear passenger side wheel area. It feels like somthing is under the car and is rattling. So a couple of days later then I got the brake discs changed and it look


You need to go to an engineer and tell him your brakes are making that sound ... 2003 Volkswagen Passat

I have never changed brake pads before in any car! Do you think I will be able to change the front brake pads on my 2003 Kia Rio? What will I need and how should I go about it? I would love a step by step "guide for dummys" kind of explanation because I am not really mechanical! Any help would be greatly appreciated!


Piece of cake....you can do it! I would register at autozone.com. It's free and you can access a full online repair manual. Anytime I purchase a different car I also purchase a Haynes Repair Manual. These are also available at auto parts stores. It w ... 2005 Kia Rio

Changed the brake pads on my 2002 Cadillac Seville SLS..but the change brake pads warning will not stop from coming on..?.?


... Cars & Trucks

2002 dodge durango...wanted to change brake pads but could'nt get calliper off. there's 2 silver rods holding the calliper in place on the backside. how do I get the calliper off to change brake pads?


The 2 silver rods should have heads on them that are bolts, about 16 mm, take them out, they hold the caliper in place and allow them to slide back and forth with the brakes. They are torqued in fairly tight, get a breaker bar on them and hang on tig ... 2002 Dodge Durango

I have a 95 mercury sable and a little while back our abs light came on well the finances werent there at the time to have it checked so now i had to change the complete brake system on the drivers rear. There was no pad left whats so ever it was smoking when i got home from work yesterday so i immediately had someone to look at them. I replaced the caliper rotor pads and had part of the brake line changed. I went to work this morning it was fine. Wasnt hot or smelling like it was burnt. I get h


If you completely overhauled the brake system with new brake lines and pads, then the problem would be that air was not completely removed from the brake system. will have to bleed the brake system to remove the air traped in the lines and behind the ... Cars & Trucks

I have a 95 mercury sable and a little while back our abs light came on well the finances werent there at the time to have it checked so now i had to change the complete brake system on the drivers rear. There was no pad left whats so ever it was smoking when i got home from work yesterday so i immediately had someone to look at them. I replaced the caliper, rotor, pads and had part of the brake line changed. I went to work this morning it was fine. wasnt hot or smelling like it was burnt. I get


Your master cylinder (rear) check valve has failed; \015\012(the pressure is not being released when the brake pedal is not pressed and, the brakes stay applied)\015\012replace the whole master cylinder.\015\012As for your ABS clean ... Mercury Sable

2002 buick century over heats unless ac is running. I changed antifreeze, thermostat, temperature sensor, coolant level sensor, and all hoses. Also coolant light won't come off even though its full. I also changed out front brake pads, rotors, calipers, hub assembly's, and axles along with rear brake shoes, brake drums, wheel cylinders, and hardware kits but brake light won't turn off. There is no problem with the master cylinder. Is there a way to reset the brake light? Just brakes did it befor


Sounds like the computer is not powering the fan relay when the engine reaches 220 degrees. You might want to jumper the temp sensor to see it it will trigger the relay. You may need a scanner to monitor the data signal from the temp sensor.As ... Cars & Trucks

I recently changed the brake pads and rotors. in the process of changing them i bleed the brake fluid to push in the caliper. Soon after when everything back into place, we tested the brakes. the brake wouldnt stop the car only when u step the brake all the way down the car will slowly stop. we replace the brake booster, but not the master cylinder it still pumps, wat can be done to solve this problem??


Bleed your brakes. new pads always take time to break in. Everytime I change a set they are never as good as the ones I replaced until after a little break in period. Do you have a high pedal or low pedal? ... 1996 Ford Taurus
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.8658 seconds