Having problems with your 1994 Dodge Ram ?

How to reset codes on 1994 Dodge Ram 1500 - 1994 Dodge Ram

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Simply disconnect the battery cable for a few seconds then reconnect.
Repair Help & Product Troubleshooting for 1994 Dodge Ram

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 1999 dodge ram 1500 3.9 ltr with 99500 miles on it. The code im getting is misfire cyl # 2. Ive changed the plugs wires rotor cap etc reset the code and it still comes back on after a second complete trip in the truck. Just to make sure my scanner was working i pulled the wire off of # 1 and sure enough i got two codes then. Misfire on 1 and 2. Reset the codes engine light went off and drove to work code came back on. Drove home from work check engine light is back on. There is no hesit

Check compression in cyl #2. If ok, the listen to injector on #2 with stethoscope and compare sound with other injectors. Remember also, that anything that slows the engine for a split second, ie acsessories can cause that crank sensor to pull up a m ... 1999 Dodge Ram

How to reset codes on 1994 Dodge Ram 1500 - 1994 Dodge Ram

Simply disconnect the battery cable for a few seconds then reconnect. ... 1994 Dodge Ram

How to reset code on dodge ram - 2007 Dodge Ram Truck

... 2007 Dodge Ram Truck


I would recheck the wires to make sure they are connected correctly:http://autorepair.about.com/library/firing_orders/bl-fo-3002.htm ... 2000 Dodge Stratus

MIL light came on so I checked it with my Actron CP9575. I have 3 codes, 1st p0052 confirmed, 2nd, p0300 confirmed, 3rd p0052 pengding. I had the 1st two codes 5000 miles ago so I replaced the high bank 2 sensor 1 which is on the passenger side the sensor before you get to the converter. The code would not erace. A friend pulled the fuse to the main computer and the code went out. That was 5000 miles ago and now it's back on and the truck is running rough. 2004 Dodge Ram 1500 2x4 5.7 Hemi. Any p

... Cars & Trucks

Started getting code 301 in March so 5mo ago got new plugs, 3 mo ago new coil packs, & fixed exhaust leak on my 2005 dodge ram 1500 4.7 magnum. 2 weeks ago changed fuel injector 1 to see if made a difference. immediately started hearing air leak. Took it to the shop the repaired my exhaust last sat and they changed all 8 intake manifold gaskets-3 bad. On Thursday stared getting a code 2302. Friday also got code 440 so took it back to the shop. The EVAP emissions hose does have a crack at end so

... Dodge Ram 1500

I have a 1990 Dodge Ram B250 conversion van the problem is the check engine light is on ran computer code to find out the problem. the engine is a 318 have a problem with the charging system have replaced the computer had the battery,alternator checked out o.k. getting fault code:1-2-40-1-5-5 what does this mean since there are no scanners available to read the computer code on this model year the van dies will not start until jumped, and it repeats the problem all over again HELP!!!!!

The numbers are 12, 41, 55\015\01212- direct batttery inut to controller disconnected within last 50 ingnition key-on cycles\015\01241- alternator field circuit- an open or shrted condition detected in the alternator control circuit. ... Dodge B Series Cargo

My 1999 Dodge Ram 2500 cummins has two code errors, P0236 & P0234. It has an intermitant power mode. Most of the time it has little power but it regains it from time to time for 1-50 second intervals, and seems completely random. I see that the P0236 code can be a MAP sensor, or too high of air pressure, and the P0234 code can be cause from lean fuel/air mixture all the way to a bad turbo charger and a bad IAT sensor. Please help me, One mechanic said it may be the lift fuel pump also.

... Dodge Ram 2500

Why wont my check engine light go off when auto store used scanner to reset code i replaced the speed sensor for code PO720. For my 1998 dodge ram conversion van

The best thing that ever happened to the parts house was having a scanner. Just because a code names a part does not mean the part is bad. it could be a wire or the pcm or a related part.\015\012\015\012There is a lot more to a P0720 code ... 1998 Dodge Ram 1500 4WD

2001 Dodge Ram, charging system not charging. No codes from the odb 2. Starts runs & drives within a few minutes the voltage guage drops to 0 & the check guages light comes on. I replaced the alternator & rechecked for codes but none show on scanner

... 2001 Dodge Ram 2500 Truck

I have an automatic 2wd 06 Dodge Ram 1500 with only 55,000 miles and I rarely haul anything. My truck's check engine light came on and it all of a sudden will run only one gear in "drive". Reverse and 1 and 2 still work. But the truck moves when I put it in any gear. I took it to the dodge shop and got a code p0700 & p0750. They were too busy to diagnose the problem and i need a ride but am nervously wandering how serious the problem is. I did put a front leveling kit on it the day before and cr

OK P0700 is just the computer alerting the check engine light software to turn on the check engine light due to a transmission electrical fault, this problem is due to a failure of shift solenoid "A". \015\012here are th ... 2006 Dodge Ram 1500

2004 dodge ram 1500 5.7 code P2302. Replaced plugs,wires and secondary coil 7 about a month ago. Now have same code on 1

... 1988 Dodge D-Series Pickups

I have a 2007 dodge ram p.u. 1500 with an engine code of p1404. Is this the egr valve sticking. i will just replace it and reset all the engine codes with my auto scanner. Is this the way to go?

P1404 is the EGR Pintle Position (system) and the faultdescription is "Circuit Fault".in reality, the best thing is to take the whole intake off and do a good house cleaning,since all the passage ways(i.e. vacuum routes, etc.)gets plugged ... Dodge Ram 1500

My p0420 on dodge 1500 ram 2002 with 91,559 miles came on. I checked and it was my catalytic converter 1 of 1. i went and bought a new eastern catalytic converter on sale for 300.00 it retails for over 800.00 drict fit replacement. It ran like new for around 45 miles and bang now the lights back on same code same mining a little slow on shift and i have a five year old flowmaster 40 series on it it at least sounds better

... 2001 Dodge Ram 1500 Truck 2WD

I just bought this truck off of ebay and it is great except i had to change the o2 sensor circuit high volt bank 1 sendor 1 & 2 and the crankshaft, now i'm getting the p1762 code and i need to get fixed so i can get truck registered, i live in tn where you have to pass emissions before you can register a vehicle, the truck runs fine, a little slow on the pickup and go but other than that it runs fine, i have a 1998 dodge ram 1500 quad cab 5.2 motor 318 automatic, any help would be great

Where in there is your question ?\015\012just go and register it if it fails emisions thy will tell you to fix it plain and simple\015\012do it on a busy day or close to clsoing time where thy might over look a small problem :) cheers ... Dodge Ram 1500

Emissions code p0456 dodge ram 1500????? and how much 52,354 miles. can I just reset code? and how Thanks and God Bless All

The code your getting is for the evaporator emissions system,look for any vacuum hose or hose that's coming from the canister tank,and check to see if its bad or has rotted and fell off,or is closed off,any one of those hoses will cause that to happe ... 2006 Dodge Ram 1500

2004 Dodge Ram 1500 5.7 Hemi. EGR valve replaced, Did a #23 Fuse pull PCM reset. Engine slow to respond slight misfire. OBD2 reading at idle 620 rpm, MAP at 10.93 inHg, time at #1 is 11 deg and ATP is 14.12%. Is a fuse pull PCM ok or should I do a Battery Terminal pull reset? Also is 620 rpm a little low? And a MAP of 10.93 inHg a little high? Thanks, Rob

... 2004 Dodge Ram 1500

Random misfire cylinder 1 code check. one spark plug wire #1 differant wire than rest hard one to get to. can't get #1 plug wire tight enough around think it is the wire, have new gas cap reset code stayed off for a while wire loosend up and check engine light came back on, thought i would replace all wires (Spark) code check it see if it runs better and reset code, you think?

Yes if it is loose can cause a misfire replace the wires as a set ... 1998 Chevrolet Cavalier

I have a 2003 dodge ram 1500 4x4 with the 4.7L engine. The check eng light is on. obd2 reads code P 0038 And says HO2S Heater Control Circuit High (Bank 1, Sensor 2). the heater is not working. How do I fix this?

Does fan run? just getting cold air? cut heater hoses near firewall, install a female garden hose bib on return and supply to heater core, first flush water thru return and then reverse direction a few times, my discharge air went from 65 to 140 ... 2008 Dodge Ram Pickup 1500

I asked the question...''I have a 2003 dodge ram 1500 4x4 with the 4.7L engine. The check eng light is on. obd2 reads code P 0038 And says HO2S Heater Control Circuit High (Bank 1, Sensor 2). the heater is not working. How do I fix this?''... I apreciate the answer. But Does this have to do with the heater in the truck not geting hot? As in no hot air, only cold blows in cab.

U need a vacuum chec-thats a common thing and it doesnt show on a scan-may also hav to inspec sensor--go to a parts place n get a repair manual-it explains how to perform chec ... Dodge Ram Pickup 1500

How do i reset anti-theft on 2005 dodge ram It won't start. It has p0513 code

Well first off you take it to the dealer as they are the only ones with the software required ... Dodge Pickup

Ok, I have a good for you! 1996 Dodge Ram, 4 x4 ,Extended cab, Heavy Half,Towing package, ect. Had new Trans installed, total tune-up,All new exhaust motor back,over sized heavy-duty trans cooler,all new brakes, ect. Here is problem: Start truck when cold, drive all day or not 5 min ride or 1-2 hr ride don't matter, after that once you need to back up and put back into drive, transmission doesn't want to shift, starts out in drive,(not first gear like it should) three tranny shops later no codes

After replacement was the system flashed with new software? this requires a reprogram of the system. ask the dealer if they have the latest programing for your vehicle. hope this helps ... Dodge Ram 1500

Auto question,I have an 96 Dodge Ram w/ 5.2L V8 eng.the problem is dtc codes P0300 and P0301,random multible cylinder misfire detected,and cylinder #1 misfire detected.Ive replaced the spark plugs, plug wires,rotor cap and rotor.what else do I need to check or change? camshaft sensor?,crankshaft sensor? coil? or do you know which sensor detects the misfire? or do I need to do a cylinder compression check?How do i solve this problem? Thanks Danny

I would check the injector. Pull the plug and check for corrosion. Use on ohm meter to check the injector. The resistance should be 11 to 15 ohms. Check it against another injector. they should be close. You can also check the injector plug. best to ... 1996 Dodge Ram 1500 Club Cab

2007 dodge ram check engine light....ignition switch check shows no problem on odometer reading. Should I disconnect the batterry to see if it resets itself? Remember....no problem code

Ya i would try that ... 2006 Dodge Ram 2500

2002 Dodge Ram 1500. 5.9 V8-518 tranny. New filter/fluid/governor pressure sensor/pressure switch. No trouble codes showing. Need to redline the engine to get it to upshirt 1-2, and 2-3. Once in 4 and 5 OK.

Sounds like valves sticking in the tranny valve body. If you did your code check with an OBD II, it would likely not reveal this. You can do a more through diagnostic at the Dodge dealer that could reveal a selenoid or sensor issue, than an OBD II ... Dodge Ram 1500
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.2450 seconds