Having problems with your 1993 GMC Suburban ?

Belt change how can i replace the belt for my gmc suburban 1993,also if you have adiagram for it

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Ther should be adiagram for belt touting under the hood on top of the grill this is aserpentine belt and there is a tensioner pully you cam pry loose with a long screwdriver or bar stick it between pluuy and bolt and pry pull bewlt off rethread nwe one and pry pully back to reinstall
If the belt is stll on make your own diagram before removing it. there usually is a diagram under the hood. There is a spring tensioner to release the belt. It takes between a 14 to 16 mm wrench or you may have a square hole in it to put a ratchet in. Real simple. 10 minute job
Repair Help & Product Troubleshooting for 1993 GMC Suburban

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Belt change how can i replace the belt for my gmc suburban 1993,also if you have adiagram for it


Ther should be adiagram for belt touting under the hood on top of the grill this is aserpentine belt and there is a tensioner pully you cam pry loose with a long screwdriver or bar stick it between pluuy and bolt and pry pull bewlt off rethread nwe ... 1993 GMC Suburban

Is there an easy way to replace the alternator/ac belt on a 2002 GMC Yukon? I changed the tensioner pulley, now can't seem to get new belt back on.


First check if the new belt is the right size by comparing with the belt and the same way it came off it gos' back on ... 1999 GMC Yukon

2003 Chevy Suburban, Alternator failed, replaced altenator and battery, cleaned terminals,and changed serpentine belt, belt tensioner is good, battery light still comes on and message "battery not charging", mechanic says it is charging, have driven 50+ miles at night (headlights) while this continues, why is the light still coming on


I would look for a short in the output wiring at the alternator. My nephew had an intermittent charging problem and I took the car to an autoparts store and had them check the alternator output. Most parts stores will do the check for free. Anyway, w ... 2003 Chevrolet Suburban 2500

I rebuilt a 350-R vortec in a 1998 GMC suburban. It runs good, except for slightly cutting out sometimes. It has a P1345 code. After erasing the code, it comes back on almost immediatly upon starting. The sensor tested bad,so I replaced it, but nothing changed. I had replaced the plastic timing cover because it said to do so. Can you help?


Hello! The camshaft sensor is not in sync. with the crankshaft sensor...When you say you changed a bad sensor and it had no effect on the CEL, which sensor was changed? When installing the crankshaft sensor the gap between sensor and crankshaft ... GMC Suburban

How do I replace the Knock Sensors on a 2002 GMC Sierra 2500HD 6.0L V8 Gas engine? How do I change the serpentine and AC belts? Last but not least how to replace the drivers front differential seal?


Remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intak ... 2002 GMC Sierra 2500HD

I just recently changed the water pump on my 96 mazda 626 I did not change the timing belt due to it was replaced about 1 year ago. during the water pump change i did not mess with the timing belt at all. I got everything back together and the engine will rotate but not start. that was a month ago. since then i have replaced the distributor, crankshaft sensor, spark plugs and have also gone back twice and did complete removal of timing belt and made sure i didn't accidently move the belt any the


Since you have double checkedthe timing and checked the battery make sure you are getting a spark at the plugs and that you are getting fuel. Make sure all sensors are plugged in and are working. Check near the crankshaft (front) for a small sensor a ... 1996 Mazda 626

I just changed thermostat, and replaced coolant, still my 1995 gmc suburban blows cold air.


Find the two heater hoses going through the firewall to the heater core both need to be hot at operating temp. If both are hot the problem will be inside with the heater control. I only one heater hose is hot the problem will be the heater core ... 1995 GMC Sierra

My 1995 GMC Suburban 2500 hiccups and looses power. I have replaced the Thermostat sensor, the fuel filter, the air filter, the spark plugs, changed the oil and oil filter. What else can be done?


... Cars & Trucks

I have changed all the pulleys except for my A/C pulley on my 2002 chevy tracker 2.0 liter engine. The serpentine belt has been changed at least 8 times over the last 5 years. i changed to pulleys in January and replaced the serpentine belt. the belt broke two weeks ago and i replaced it. The same thing happened yesterday. What would you suggest i do to start troubleshooting the problem.


REPLACE THE TENSIONER IDLER PULLEY.THE TENSIONER IDLER PULLEY MAINTAINS THE BELT TENSION WHEN IT GOES BAD.THAT WILL LEAD TO LOOSE BELT TENSION CAUSING BELT TO BREAK. ... Chevrolet Tracker

We just took our 2001 525i bmw in and had the oil changed, filter changed, spark plugs replaced, alternater belt and a few other belts changed, two power steering lines replaced and a leaky gasket replaced. My husband is now smelling what seems to be oil and just has noticed a small amount of smoke. Could this be from the repairs they did and it just needs to burn off, or could they have missed something and we should take it back in?


Yes TAKE it back in!!!!! This is most likely do to the repair of the leaky gasket. Look at you receipt and find what gasket they replaced. Then look at the area around the gasket. (use a flash light ) You should see oil signs. This is normaly caused ... 1987 BMW 3 Series

My car was running perfect until the guy change the 3 spark plugs located in the front of my car.the back has never been change yet. so afta that he also change my low beams on my headlights,i had already replace my serpertine belts and everything previously before i came to this problem ,heard like the whistling sound like wen u warming up your car on the belts,he poured brake fluid afta replacing my spark plugs he had the nxt day i was supppose to return to the same guy so he can change the b


Check the all the pulleys to see if any are seized, they should all turn freely, and your car belts shouldn't squeel at all ( loose belt, worn belt, bad steering pump), don't know what your talking about the brake fluid, did your low beams work befor ... 1996 Buick Riviera

Timing belt i had a timing belt changed 6 months ago with the kit. a friend bought my kia she went to get a muffler,they recommed the timing belt to be changed when they changed the belt could they tell if this was a new part already replaced. They said you could not possiable tell if it was changed or not, is this true. pam


The only true way is if on drive side has all of the marking on it or if someone had a receipt for a timing belt, so a true Mechanic would know if it had been replace recently or not ... 2000 Kia Sportage

Hello everybody, I have 1998 GMC Jimmy and after replacing the worn out AC belt with a new ones squeaking noise (when its cold) is gone BUT some "TUG TUG TUG" noise appear and it sounds like behind the radiator. It's been a week now since I replaced the belt but the noise is still there, can any body tell me what it is? 2nd Question; How would I know or when should I replaced the timing belt? I got 215k in my car now. Any help or suggestion would be appreciated. Thank you.


Can't help you with the noise, but I suggest that you remove the belt and check all pulleys for any roughness or binding when turned by hand. You have a timing chain...You are right in the "window" where I've seen the most failures. It;s time to chan ... 1998 GMC Jimmy

Timing belt i replaced the timing belt got the car to start..first problem...it started but the drive belt tensioner wont stop moving now and it is making a knocking noise everytime it bangs ...second..the car wont turn off when i turn it off it will run for like another minute or two...third i have a broken throttle position sensor..will replacing the throttle position sensor and the drive belt tensioner fix my problems...or did i not time the engine right when i changed the belt..keep in mind


You obviously need to replace your TPS, and you may need a new belt tensioner as well. On these cars the timing belt setup is not about no 1 cylinder being top dead center. Here are the proper steps to do a timing belt on this vehicle:\015\012 ... 1996 Ford Escort 4 Door

Belt question Hi. My friend was told her serpentine belt on her 1999 mercury villager was defective. She was at an "oil change only" place. I checked and saw the Fixya for a 1993 village serpentine belt replacement. That looked like the timing belt replacement procedure. Are there other postings for just the front main belts?


You should clarify which engine it is, and you can look under the hood near the radiator for the serpentine belt instillation diagram that is on a sticker. Rick ... 1999 Mercury Villager

1999 Chrysler 3.5 liter engine Changed timeing belt ,water pump, and belt hydraulic piston for belt teninsioner. Car would crank but would not start. Rechecked timing marks none of the three (crank,and both cams)will index.I suspect that the crank rotated as I was torqueing the damper wheel bolt since the damper wheel is not keyed to the crank.I had to replace the radiaitor due to it leaking and then decided to replace the timeing belt ,water pump ,and belt tenisioner. Since the engine has be


If you cranked this engine with the belt off u have bent the valves, I have the factory manual for this engine and they bend valves if belt is positioned incorrectly or not on when engine is cranked, sorry but that is how they are built. ... Chrysler LHS

I went to have oil and filter changed on my 92 gmc sierra he also replaced catalytic converter because it wouldnt pass emission test. I get the truck home and there is oil on my driveway where we had parked the truck, so I cal the guy and he comes for the truck, calls me and says the lines is where oil is coming from and he can't just replaced the couplings. He also said once this happens the lines will have to be replaced every time I change the oil because it will leak and that this always hap


Something here is fishy, take the truck to a Chevy dealer and explain the problem. have them inspect the problem, I am 100% sure they can fix this issue and the other tech? well he sounds like he is just inexperienced or short of your money in his po ... GMC Sierra 1500

I just bought a 2007 Town& Country Van with only 8954 miles. What is the sevice that should be addressed now with such low milage yet already 3 years old. I have just replaced the battery, changed oil and filter,replaced back bulbs.After the next oil change i will be using snyc. New tires with front end aligment and all braking pads will follow in 2 months with new a.c. filter and new air filter with pcvs also replaced. All pulleys and serp. belt will be checked out again as will spark plugs


You are going through a lot of expense,oil and filters for sure, tires maybe depends on their condition, when you fill the tand add a bottle of injector cleaner, as for the rest a good inspections should be all needed, hoses and belts not cracked or ... 2007 Chrysler Town & Country LX New Cars

When should the timing belt be changed on the 2.5L engine in my 1998 Chrsyler Sebring JXI Convertible? An independent service garage recommends replacing it at 100,000 miles; owner's manual doesn't list timing belt change for this model but does call for changing it at 105,000 for the 2.4L engine.


The recommened mileage is 105,000 miles, the reason the shop wants to do it early is that if the belt lets go you will damage the engine, call it insurance ... 1998 Chrysler Sebring

Replacing belts What does it take to replace the small belt on the engine of a 2002 GMC Yukon? I noticed there are two belts on the engine.


This is your a/c belt the tensioner has a spot for a 3/8 ratchet to fit in also the main belt will have to come off also to get belt off ... 2002 GMC Yukon Denali

I have a 2003 Kia Sorento needing replaced belts, 3 serpentine belts. I have the replacement belts i just need to know the procedure for changing them out.


... Kia Sorento

T-belt replacement I've done t-belt replacement before on other models but not on 2000 subaru legacy "L". I am not sure how to do TDC on this subaru automatic 4WD. I read Hayes manual but still don't understand it. Is it more difficult to change t-belt on this car than any other models? Any help is greatly appreciated.


The haynes manual makes it sound worse than it is !!!!, once you get all the extra,s out of the way ( radiator etc) its not too bad ... the are marks on all pulleys and on the heads,line everything up before you start and realign as you go ( things ... 2000 Subaru Legacy

How do you replace the fan belt of a 1996 GMC Jimmy ? After replacing the belt tensor I see no movable part in order to place the fan belt.


The tensioner is spring loaded .. you can use a box wrench or somtimes a ratchet wrench (into a square hole) to pull against the spring in the tensioner such that the belt is easily installed .. a lot easier if you have three hands but doable if you ... 1996 GMC Jimmy

The timing belt was replaced by a mechanic...worked fine 1 full day and driven 80 mph almost 200 miles...second day would not start ...as all idiot lights cam on...same mechanic says there is a problem in the cylinder furthest from the water pump(which was replaced at same time as t belt) can the timing belt change have caused a cylinder problem...??? thanks, bill


Its really hard to say what he did was done correctly. you have some excellent mechanics and some below average no different than a doctors to lawyers. just to say if that mechanic dint put it on back correctly, yes anything ... 2001 Volkswagen Beetle

2000 NB 1.8 L Turbo Had the timing belt, waterpump and tensioner replaced New in Dec 05. 91,000 k Was told today that the belt is cracking and waterpump is leaking. 157,000k. How long do waterpumps last, I bought a one with an steel impeller. Could belt be broken down by coolant? Should I bring it back to VW and get them to fix it? I did not see the old components when they replaced them, could they have not changed them? I don't know what to do as I cannot afford a new car and don't want this


I think the recommended replacement interval is 65-75k for turbo engines. so might just be due for another timing belt job! ... 2000 Volkswagen Beetle
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.3034 seconds