Having problems with your 1992 Chevrolet Corvette ?

When i hook my mac mentor code scanner to the obd 2 link in my 92 corvette, it says no communication with ecm

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

There are two scanners, one for 1995 and older, the other for 1996 & newer.
Repair Help & Product Troubleshooting for 1992 Chevrolet Corvette

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When i hook my mac mentor code scanner to the obd 2 link in my 92 corvette, it says no communication with ecm


There are two scanners, one for 1995 and older, the other for 1996 & newer. ... 1992 Chevrolet Corvette

When i hook my code scanner to my 92 corvette it reads no communication with ecm


... Cars & Trucks

I have a 2002 suzuki xl-7 that keeps dying. when i does ses light flickers then goes completely out. no codes. as soon as i plug an obd scanner ses light comes on as if the vehicle got ecm signal again. ses goes out as normal when you start the car and vehicle runs perfect no codes or anything as long as i leave a scanner attached. I suspected computer. computer has all power and grounds so i'm stumped. checked things like maf map cmp ckp all ok


... 2002 Suzuki XL-7

Replaced ecm now truck will not run, cranks over and starts then dies. Scanner says security code must be reset, how do you doit


Depending on the year make and model, you would need to have the dealer program the new computer with their scanner. ... Cars & Trucks

P1660 code fans wont run tried everything replace coolant temp sensor,3 fan relays , 50 amp fuse still fans wont run so i installed jumper wire with fuse link fan runs now but still have code p1660 my scanner said it was a high idle lamp control circuit but looked it up on internet and it says that p1660 is code for cooling fan control circuit


... 1999 Cadillac DeVille

P1660 code fans wont run tried everything installed jump wire with fuse link still run but still have code p1660 my scanner says its a high idlea lamp control circuit looked it up on internet said p1660 code was cooling fan control circuit


... 1999 Cadillac DeVille

Obd scanner says no link


Chances are there is a blown fuse for the computer.Is the check engine light on when you turn the key on ? ... 2000 Oldsmobile Intrigue

Oyota 4runner check engine light- how to check? I have a 99 4runner 4wd v6. Check engine light just came on. Dont have one of those obd scanner things and I was wondering if anyone had a link on how to get the error code without the scanner. Thanks!


no\012way without a computer, if you have a parts america or maybe even auto zone\012will do it but they will hook it up and tell you the problem for free.\012\012 ... 1996 Toyota 4Runner

2001 isuzu npr 4.8 diesel abs light on and cannot connect to ecm with my obd 2 scanner. Can i get codes without obd 2 ?


... Cars & Trucks

1993 corvette (non ZR1) that began to stall when driving 3 weeks ago. Suspected a fuel issue as the car would just "shut down" while driving as if the fuel was shut off. Mechanic replaced the fuel pump, fuel filter, and fuel pump relay switch. However, it will still stall. Sometimes you can let it sit for a while and it will restart, or starter fluid into the throttle body will get it going again until it stalls again. There are no codes on the ECM according to the mechanic who says the ECM chec


The distributors give this vehicle a lot of problems,because of the location of the distributor,The cause of your problem is,no injector pulse,most likely,you will have to replace the pickup coil in the distributor,and my advise,is to replace the pic ... 1993 Chevrolet Corvette

2.8 calv hey I am working on a 1988 chevy Z24 with the 2.8 at 1st My sacnner would not link up so I change dout the ecm and fixed that problem ,but the car will start up and run for about 15 to 20 mins then shuts down I have good fire as well as fuel ,I removed the control mod and had it tested to see if it was breaking down under heat but it passed all the test ,The only code I get from my scanner is a code 43 for knock sensor ,have you ran into injectors breaking down and shorting out injector


Remove the air horn and check the resistance of the fuel injectors they should all be about the same ... 1988 Chevrolet Cavalier Z24

I have a 99 passat v6, my check engine light went on, and the scanner says code P0112- air intake temp circuit low input. I replaced the sensor and erased the code from the ecm, but the light comes back on again, what can I do to fix this???


Remove your battery head for 5 minutes while engine is off. This should put it in order.\015\012\015\012Rate this please. ... 1999 Volkswagen Passat

The error code P0161 came up on my 2003 rav 4 auto...wch when read with the obd scanner means sensor heater malfunction bank 2 ..pls cud some1 help me in identifying the location of this sensor n what are the consequences of driving the car with this particular code being on?..also any link to sites where i can purchase this sensor?


... 2003 Toyota RAV4

What could be the problem with my car, premio 1998 d4 engine, i have to start for several times(3) for the car to start.(hard start) it has engine check code 12,which has failed to clear up even after replacing crank and oxygen sensor and also clearing the computer memory by removing battery terminal and wait for 20 min. i recently purchase Eobd/obd2 code scanner could not link with ECM, what could be the possible DTL connector, pin layout are 4,6,7,9,13,14,16. Anyone with an idea?


DTL connector is the plug is under the hood on that car i think by the driver side ... Cars & Trucks

Scanner obd 2 pulling up these 2 codes P0352 and P0353 saying ign coil b and c malfunction circuit ? Where do i find band c coils?


... Cars & Trucks

My obd ll code reader is saying failed iso link


... Cars & Trucks

Nissan Titan my code reader obd ll say failed iso link


Your going to need a professional scan toolwith enhanced data,to continue, as well as factorydaignostic charts & info ... Cars & Trucks

I just replaced the ecm on my 2004 f150 and you still cant put a code reader on it. It says it won't link. the truck bogs out when you accelerate and runs very rough.


... 2004 Ford F150

Problem is a hard to start & when idleling it dies im trying to put scanner but it say there's no communication to ECM


TRY CHECKING THE FUSES FIRST. A BLOWN FUSE COULD BE THE ONLY PROBLEM. I HOPE THIS HELPS. THANKS FOR USING FIX-YA. PLEASE KEEP ME POSTED, ... Toyota Matrix

My 06 escape abs light is on all the time while driving. I hooked up my Actron OBD II auto scanner and I'm getting a "link error" so I can't get any codes. I'm not sure if these are related. Anyway I need to know how I can troubleshoot the abs system to determine why the light is coming on. [email protected]


Aftermarket code readers will not read abs codes... only the ford scan tool will read the code. youve most likely got a broken tone ring on one of the axleshafts...quickest fix would be to replace the axleshaft, but you can buy the ring seperate and ... Ford Escape

Obd 2 connector does not work with any code scanner


HI there....Check to see if the code reader is a CAN OBD 2 code reader. If it is only OBD2 , that may be the problem. In 2003 Some vehicle manufacturers ( ford,Gm,Mazda and Saab) began using a new computer protocol called Controller Area Network (CAN ... 2004 Chevrolet Tahoe

Plymouth breeze wont start just turns over. i've replaced coil ,plugs, camshaft sensor. obd2 scanner says no link or 0 codes. is this because car battery is not charged?


You need battery power for the computer to fuction, so yea get the battery charged up first. ... 1997 Plymouth Breeze

2005 nissan sentra with 1.8 liter motor with 57000miles started chalking and running rich with no obd code, I tried to replace air flow meter throttle body from junkyard no luck, I send car to dealer for ecm replacement under warrenty, they saying it has bad all injectors bad and need to replace throttle body, what is your advise you have help me bunch of time, itrust you


Yes it can be dirty fuel injectors causing your problem, a dirty injector does not emit a good spray pattern , the spray must be a fine mist and a dirty injector will emit large droplets of raw fuel that will not mix well in the intake manifold causi ... Nissan Sentra

2007 chevrolet suburban check engine light came on after "tighten fuel filler cap" message, also the remote start wont work now, pep boys says they cannot communicate with obd II scanner and it must be an electrical issue their is no blown fuses under the hood is their any additional fues elsewhere


The OBDII connector is on the same circuit as the cigarette lighter. A lot of times a cell phone charger or other device will blow the fuse and cause the scanner not to power on or communicate. I would just double check the cigarette lighter fuse. Al ... 2007 Chevrolet Tahoe

92 camry with 2.2 a/t no currant to computer or distributor checked alot of relays fuses and there is no power to the 10 amp fuse that is located by the computer nor the relay and the 30 amp fuse. so i try to use a scanner to read codes and the computer is not communicating, note in the engine compartment there is a 30 amp fuse that says am2 its supposed 2 b for the head lights and the one blows everytime I open the switch, I dont have to crank it I only open te switch,and the head lights still


Have a auto electrisian check the wiring if there are no shortsin the system ... 1992 Toyota Camry V6
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.3770 seconds