Having problems with your 1991 Nissan 240SX ?

This is about my Nissan Figaro does not start since the ignition

\015 This is not about a Nissan 240SX! My 1991 Nissan Figaro automatic 1 litre turbo (based on a 1990 Nissan Micra, made in Japan) does not start since the ignition has been replaced, is there a wire that has been missed? There are two connecter blocks on the wiring on the lock. Can anyone advise please.\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 1991 Nissan 240SX

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

This is about my Nissan Figaro does not start since the ignition

... 1991 Nissan 240SX

My 95 Nissan Pathfinder will not run over when the key is turned on. Out fo the blue, I tried to start and will not. I turned the headlights on to see if there is actually a drain on the elctrical current when turning the ignition key on and the headlights do not even diminish brightness, as they should when turning the ignition key to start. The battery would seem to be okay since their should have been a drain with turing the ignition key to start. Just out of the blue with warning


I have a 2007 Nissan Versa hatchback. My keyless entry has stopped working on both keys and I have to pull out the actual key in order to unlock the door and start the ignition. Is this a battery problem or a fuse? I am assuming a fuse issue, since neither fob works.

... 2005 Nissan King Cab

I have a 2003 Nissan Altima 2.5l recently replaced radiator myself and since then my check engine light came on for misfire ignition #4...after a cold night went to start car and sounds like car wants to turn over but wont. I'm not sure if its the misfire that's causing the problem or something to do with fuel not getting to the engine. I checked the fuel pump and it sounds like its working when I turn the key. I've tried holding the gas pedal down while turning over and got nothing. Any suggest

Remove plugs and check. make sure that the plug gap is not closed causing misfire. we have some issues with power valve screws coming loose and getting inside of the cylinder closing the gap on plugs. some power valve plates come loose also and get i ... Nissan Altima

2005 Nissan Sentra - all of a sudden from out of no where I came out of the grocery store and the ignition turns but does not start! My check engine light comes on and off and has for the last yr and half but I took it in 6 mo ago and the fixed the sensor and replaced the fuel injection system. No problems since til today. The battery is good and the alternator belts are running smoothly. What could it be? FYI small pin leak in power steering but they said it was too small to do anything wi

Most likely the starter is faulty. It could also be the starter relay or damaged/ loose/ corroded wires to the starter. Also, I'm not sure who told you the power steering leak was "too small to do anything with", but if there is a leak in the pump, s ... 2005 Nissan Sentra

We have always had a starting issue since we hit 50000 miles. the ignition cintol module has been replaced, along with crank position sensor, cold start sensor, battery, cables, evan the oil pressure sensor,but to no help. now are mechanic thinjs it is the wiring harnes that is connected to the ignition module, if the car wont start we just move the connector and it starts sometimes, we have spent alot of money on this car and I need some expert advise since is is going in the shop again.

The connection is loose or broken ... 2004 Chevrolet Impala

My 2004 Nissan Sentra 1.8 won't start, battery tested great, had a cranking problem for past couple years, only starts on third crank, but this time on 2nd try, there was a slight "tzzt!" sound by the ignition switch, then no sound, no click no nothing. I hooked it up to jump start, when I was about to put the key in the ignition, heard that "tzzt, tzzt" sound again. It did start with jump and drove it home, but won't start again. Is that a starter problem or ignition switch short?

Could be starter or solenoid. you can test them with a voltmeter and see if they ohm out. which means there is a clear path with some resistance. ... 2004 Nissan Sentra

I have a 1995 Nissan Maxima that want start when I put the key in the ignition to start the car; especially when it's cold out. I've developed a hard blister on my index finger from trying to start my car, do I need a new ignition w/key because I've had several keys replaced because they have broken off in the ignition. I've replaced everything from the starter to the battery what could be the problem?

If you are twisting very hard or have to wiggle the key to get the starter to engage, then i would say so. Either that or you could replace the start portion of the switch with a push button on the dash, Just like the new in vogue sports cars have. ... Nissan Maxima

My 2001 Chevy Cavalier's ignition is stuck and the key will not turn and I took my Title to the dealership and got a new key made and it still will not turn so.....Since it was stuck somewhere for a couple weeks I didnt want it to be I took off the black box from the back of the ignition that starts the car and got it started and drove it home and now it will only start for a second and shut off,I cant get the ignition out for replacement because it will not turn in order to pull it out....So wh

... 2001 Chevrolet Cavalier

I was driving to work and the truck stopped running. When I came to a stop I tried to restart it and it turned over but would not start. I had all panel lights on and it still would not start. I turned the ignition on and off several times, thinking maybe it was something in the ignition switch. After about 20 minutes of this and trying to start it, it finally started. I was able to drive it about 3 miles back home and I have not drove it since. When it did finally start it was kind of flo

This appears to be an ignition problem and will require testing with a volt meter at the least. It could be the ignition coil due to the fact that the vehicle was most likely @ running temperature when you experienced the engine shut down. When coils ... 1997 Dodge Dakota

I have a nissan almera 1.6 , got ignition lights, battery is fine but does not start??? Iv had this problem before it usually starts on the 3rd turn but eventually goes dead and does not start at all, previously I changed the solonoid and it worked perfectly for about a year, there is a clicking sound from the bonnet each time you try to start it with a continuous buzzing sound when the ignition is turned on, do I need to replace the solonoid again? And what could be the fault for this to be hap

... Cars & Trucks

Ignition switch I have a 96 dodge 2500 diesel,once in twenty times this happens,turn switch to start position, it cranks over but no start, after the third try it will start,also a month ago the heater fan refused to work momentary, the temperature control unit was new six months ago. The engine not starting is a electrical problem not fuel. Could this be the ignition switch since both problems go through the switch? thank you,ken

Next time this happens leave the key in the on position, open the hood and lift the fuel solenoid link (between the fuel solenoid and the injection pump) up. If it stays up the truck will start and run. The solenoid is shot but that might be a sympto ... 1996 Dodge Ram

1999 Peugeot Diesel Estate car has developed starting problem, when turning key in the ignition the glow plug light goes out as it should do but the car will not start first time, only starts when ignition is operated 4 or 5 times then a big plume of white smoke comes out of the exhaust and she finaly splutters into life, problem has only developed this week (since weather has turned colder) she is due a service and oil change could this be the problem?

Hi you seem to have worn out glow plugs.. cheap and easy diy fix!! ... 1989 Peugeot 405

I have a 2002 Nissan Altima with 38,000 miles on it, and had problems starting. Took it to the local Nissan dealer and they say it's the mass air flow meter, and they want to charge me over $500 for the part alone, plus another $200+ for labor. I think that's outrageous, since others sell the same part for $225. Is it feasible for me to buy the part myself and replace it? I have rebuilt engines in the past, but I don't have any of the fancy computer gear. hard starting or no start in cold weath

Ya u can d it.u try to cahnge oil filter check that petrol is rich to its destination.and chnge spark plug to . ... 2002 Nissan Altima

I have a 2003 cadellac deville that will not start. There seems to be no power from the ignition out. I have checked the started and it is good. Someone changed the key ignition around 3 months. It only started once since then.

It could be the neutral safety switch which prevents you from cranking the engine in gear.But it could also be the anti-theft system. The system reads the chip in the key to allow the starter to crank the engine.Is the security light staying ... 2003 Cadillac Deville

2000 nissan frontier 6cyl 3.3l will not start. pretty sure it is either the crankshaft position sensor or camshaft position sensor. since the truck wont start and I dont have an obd scanner I can't narrow it down between those two parts. I bought a CKPS since it was only 20$ but I can not locate where the sensor is.... does anyone know where it is? Also, is it true if its the CMPS, i would need to replace the whole distributor? Which sensor is more likely to fail and cause it not to start?

... 2000 Nissan Frontier

1998 renault megane ignition problems. My wifes Renault megane scenic 1998 has has nothing but problems since we bought it. The most recent being as follows. I was driving the car and stalled it. from then on the car would not start. key in ignition lights the dashboard which flickers at first, then settles. headlights dim upon attempting to start. engine does not turn over. jump starting the car with jump leads gets it running. once running the car has a flashing 'heart monitor' style warning l

It sounds like one of three things are happening\015\0121.your battery has adead cell in it and does not have enough cracking amps\015\012\015\0122. your alternater isn't charging your battery enough\015\012\015\0123. yo ... 2000 Renault 181

1997 Pontiac Bonneville starting issue: My Bonneville would start immediately regardless if the motor was cold, hot or in between ever since the car was new. Two weeks ago it would start immediately if the car was cold or at the operating temperature of 190 degrees. If the car cools down between 100 - 150 degrees the ignition must be cranked for 15-30 seconds and gas pedal pushed sightly to acheive ignition. Do you think there is a faulty temperature sensor or something else?

First thing to do is replace you fuel filter, If there is a check engine light have the code read, Most parts store will do this for free. Get the code number type that into google for further advise. ... 1997 Pontiac Bonneville

1987 Toyota mr2 4age won't start. head gasket blown and added sealer, but won't start now. engine turns and rumbles a bit w/ a slight backfire. Before tearing the head off or swapping motors, I was thinking of trying a few shots of starter fluid to see if it starts. If it does, then I'll have to track down whether it's a fuel problem or ignition. Since it sputters and gives a single "pop" before just spinning and since I replaced the old gas tank and found tons of rust in it. I suspect that the

... 1987 Toyota MR2

Just got my ignition replaced with a used ignition and since then now and then I turn my key and everything in the car and outside turns on. Gas pump kicks in and everything then I go to start my engine and the key turns and nothing happens. No click, no nothing, I have gotten it in the past to turn over from rapidly turning the key to start the car and then randomly it would start up. But now it has finally stopped working. Anyone have any ideas?

Ignition switch went out, but that doesn't explain lights coming on. I would check for burnt wires under the dash. if none are visible you will have to cut into the harness. just be carefull doing so. you don't want to cut any computer wires ... 2000 Oldsmobile Intrigue

Hi, 2006 Nissan Sentra, The car won't start, I can hear the pump as I turn the ignition on, as I try to start the car is turning over okay so no starter problem and battery strength is okay. I had removed one of the ignition coils to test looks like I am not getting spark. Ignition coil fuse is 15amp is okay. Any other simple things to check ? I am about to take it to the dealer Thanks Justo

I have an 06 sentra as well with a similar problem. Just pop the gear shifter into neutral and then turn the ignition. The car should start. It always works for me. ... 2007 Nissan Sentra 2.0 SL Sedan

In a 2001 Buick Regal please tell me what might be the reason behind the ignition key being unable to place the ignition switch in the off position so as to remove the key.... (Note: I can remove the key in the last position before the the "off position" and as a consequence the car can be started in this position without the key since the power is still going to the system.) The battery drains down after 3 days but the car continues to start and can be driven but the ignition switch lock

Yes You Are Correct in that the IGNITION LOCK CYLINDER IS FAULTY, and Requires Replacment.FAIRLY COMMON Problem. ... Buick Regal

2006 silverado wt 1500, had a remote start system installed and power locks. Shortly after the truck wouldn't start at all anymore. So had the remote start disabled but the power locks still work. Since the remote starts been disabled the truck starts fine everytime. The dealership tells us its the remote start, the business that installed the remote start is blaming the ignition for being faulty. Tryin to get a straight answer as to we have 2 of these trucks, and the other one is fine with the

If you are still using the compustar remotes and they are working then the remote start is still hooked up. What did the dealership say exactly? What is the shop telling you. The dealerships likes to blame everything on he remote start but if they ca ... 2006 Chevrolet Silverado 1500 2WD

Hi i have a nissan 300zx 1991 twin turbo manual . It is far from standard running 395.2 bhp . It has a single ' sigma ' fob wich does not open the doors and does NOT appear to set an alarm . I have had the car a week and this has happened several times but usually resolves itself within minutes but last night it didnt and still will not start . What i had to do to start the engine was press the fob once i am in the car then insert key into the ignition turn so ignition lights are on press button

Hi! As as a first course of action please open the hood and remove the positive battery connector. Let it sit for atleast 5mins to reset the system and you may get your car back to it's normal operation. Hope this helps and thank you for using FixYa! ... Nissan 300ZX

My 2003 grand prix pontiac keeps blowing a fuse. It won't allow me to take the key out of the ignition or when I start it to put it in any gear, like the gear shift is stuck. And since my keys are stuck in the ignition I cannot lock my car with the drivers door open. This has been going on for about 5 months and we have put around 8 new fuses in. The first 2 times it happened it took a while for it to blow again but now i start it once and it blows. It is very aggravating and my mechani

U will have to find out what all is on that fuse and find the short ... 2003 Pontiac Grand Prix
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.3801 seconds