Having problems with your 1991 Jeep Wrangler ?

Where is the bleed valve for clutch on a 1991 jeep wrangler

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png
The location is in the same place as a 92 Jeep, it's on the slave
cylinder. follow the break line from master cylinder down to slave cylinder.
the bleader is on that cylinder.
Repair Help & Product Troubleshooting for 1991 Jeep Wrangler

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Looking for picture of clutch bleed valve - 1991 Jeep Wrangler


On the drivers side of the bellhousing the bleeder valve it located on top of the clutch slave cylinder ... 1991 Jeep Wrangler

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fl ... 1991 Jeep Wrangler

Bleed the clutch on a 1992 jeep wrangler - 1991 Jeep Wrangler


... 1991 Jeep Wrangler

Clutch how do i bleed the clutch on a 1990 jeep wrangler? i can't find a bleeding screw


Bleeder screw should be somewhere on the slave cylinder, generally somewhere above the centerline of the unit. (unless someone snapped it off. If that's the case, sometimes you can drill it out, but this takes a lot of skill mixed with some luck. (Yo ... 1990 Jeep Wrangler

Need to bleed jeep tj clutch - 1997 Jeep Wrangler


... 1997 Jeep Wrangler

I have a Jeep Wrangler 1992. Replaced rear axle with a Ford 8.8 axel rear end and installed all new brake rotors, callipers, hoses, metal lines, forward brake discs, hoses. Have bled reapeatedly....pumping and numatic suction brake bleeders. Still no brakes. Will not build up pressure. Wondering about the prop. valve? Opened it and cleaned it...looks fine. I think brakes work fine...wife disagrees. Unable to get brakes to bleed could the prop. valve be to blame. Followed all instructions in Hane


The proportioning valve most definately can be the problem. Did you change it or is it the original? (A disc/drum system uses a 70%front/30%rear braking ratio, whereas an all-disc system is alot more even). I would first bleed the master cylinder. ... 1992 Jeep Wrangler

I have a 1988 jeep wrangler when i let it sit for a little bit i have a little bit of clutch pedal but after i bleed it. theres nothing at all. Then i let it sit and it will get a little better but then i bleed and the same thing nothing. i can't get a good pedal


It sounds like a faulty clutch slave cylinder. If you cannot keep pressure, then this is where to start. bench bleed the clutch master first if possible then when installed in the car be sure to get ALL the air out then continu on from there. If n ... 1988 Jeep Comanche

I have an 01 Jeep wrangler within the last year the clutch assembly and components have been replaced. I let my vehicle sit for about 3 weeks and now the clutch will not disengage. It is almost like it has air in the line but when I was looking for the bleeder screw there is not one. Like I said it is a replacement master, slave and everthing else. I need help I really need to get this thing running for the fall. Any suggestions on how to bleed the air out without the bleeder screw I used the Ha


You'll need a friend\015\012\015\012Hold down the clutch (Not running) and crack loose the line fitting where it goes into the slave cylinder, be sure the master cyl is over full to allow for lost fluid\015\012\015\012that sho ... 2001 Jeep Wrangler

1990 jeep wrangler just got all new master/slave cylinder pressureplate piolt bearing or throughout bearing / had flywheel refaced had pedal frst time engaded and second time no pedal and third time had pedal about two weeks now and no pedal. tried to bleed. i short stroke the pedal pertty fast to work air back to top. i keep getting air bubles but no leakes even when i don't bleed every thing is new. if i take hydralic line off at master cyl. and hold my finger over it and go to ingage clutch s


You have to bleed it at the slave cylinder not the master cylinder.Keep the bottle on the m/cyl full at all times and do not disconnect any lines.Bleed the system at the sl/cyl.Then do it again after a short drive.You still have air in the system.If ... 1990 Jeep Wrangler

Trying figure out how in the world to bleed my clutch on a 1991 Rodeo. I replaced the slave cylinder, tried bleeding it at the slave cylinder and the intermediate bleeder valve on the side wall of the engine compartment, by opening the slave cylinder bleed valve, depressing clutch pedal, closing bleeder valve, pulling the clutch pedal back up. After doing this 400-500 times, no progress. I bought a vacuum/bleed system and hooked it up to the slave cylinder bleed valve and while system was fully


... 1991 Isuzu Rodeo

Where do you bleed the hydralic clutch on 1998 Jeep Wrangler 6 cyl.


I believe that you can try this at line down on side of transmission but if unsuccessful the whole kit costs about 150 dollars and it brings reservoir, lines,slave cylinder and pump for pedal. the way to bleed it is to open line or bleeder and let fl ... 1998 Jeep Wrangler

How to bleed clutch air in line 2000 jeep wrangler


... 1992 Jeep Cherokee Sport

How do you bleed hydraulic clutch system on a 1993 jeep wrangler


... 1993 Jeep Wrangler

Looking for a diagram for a 1999 Jeep Wrangler Sahara that shows photos on how to find the bleeder screw on bleeding the clutch


You wont need a photo its super easy, but it is under the jeep follow the line from resivior to the clutch master cylinder (holds fluid) then the other end located on the trannsmission is the slave cylinder the bleeder is on it usually has a rubber c ... 1999 Jeep Wrangler

How do i bleed the clutch slave cylinder on a 95 jeep wrangler


Pump up clutch pedal really fast about ten times....leave it held to floor....open bleeder on slave cyl... repeat untill you have good pedal....may need to adjust master cyl. rod on clutch pedal to get more travel....good luck....Lee ... 1995 Jeep Wrangler

2000 jeep wrangler how to bleed air in clutch line


Did you replace any parts, or did the clutch pedal just go out? ... 2000 Jeep Wrangler

How do you bleed the clutch in a 1991 Jeep Wrangler?


If replacing just the fluid, you should gravity bleed it by opening the valve at the side of the transmission where the line goes in to connect with the slave cylinder. Be sure to stand by and keep the tiny reservoir from going empty during bleedin ... 1991 Jeep Wrangler

How do I bleed hydraulic clutch in 1991 jeep wrangler


There is a bleeder on the drivers side of the transmission follow the tube from the clutch master cylinder if you cannot find it. Pump the clutch up and hold it down then open the bleeder repeat till air is gone. May have to bleed again after driving ... 1991 Jeep Wrangler

When bleeding the clutch on a 1990 jeep wrangler, the fluid just leaks out of the bottom of the trans. What is the problem? How do I fix?


Is the slave cylinder inside the bellhousing?? ... 1990 Jeep Wrangler

I need to bleed the clutch on my 1992 jeep wrangler and need to know were to locate the bleeder insert


The bleeder valve will be on the slave cylinder. Follow the hydraulic line from the Master Clutch cylinder down to the slave cylinder by the transmission. ... 1992 Jeep Wrangler

How do you do you bleed a clutch line on a 1993 jeep wrangler?


Just like you would bleed brakes. Fill the reservior with brake fluid, open the bleeder screw and have a friend press the clutch pedal in. Close the bleeder screw and let up on the clutch. Do that until the clutch pedal has a good feel. Be sure to ch ... 1993 Jeep Wrangler

The clutch in my 92 Jeep Wrangler suddenly stopped working.


It is a bleeding problem try to bleed it more then adjust the clutch release adjuster under the pedal make it around 2 inch proximate. ... 1992 Jeep Wrangler

How do i bleed the master clutch cylinder system on a 1995 jeep ?


A special pump is used to back bleed the system. If you don't own one then you have to be patient and just keep pumping the clutch pedal until it comes back. It can take a half hour to get it back. Just depents on how much air is inside. ... 1995 Jeep Wrangler

HELLO EXPERTS I have a 1995 jeep wrangler with 2.5 engine and five speed trans. I've put about 1000 miles on a new clutch, pressure-plat, throw-out bearing and slave cylinder. I am experencing the following problems: 1. With the clutch pedal fully depressed the clutch remains engaged and jeep wants to move forward. The engine has died at stop signs when the clutch and brake are fully applied. 2. When moving the trans refuses to shift and has to be stronged armed into the next gear. With resultin


Check all your hydraulic connections for seepage . If you find nothing leaking, check where the rod goes into the master cylinder under the dashboard...If still nothing, I'd change the master cyl, as it is likely internally bypassing and permitting t ... 1995 Jeep Wrangler

I have a 2004 Jeep Wrangler. The Engine light came on. I had Auto Zone check the code for me. I don't remember the number, but they said that it was the Purge Valve. I had to buy the Purge Valve from the dealer, because Auto Zone didn't have it. I Put the Purge valve on, and cleared out the code. The Jeep light stayed off for about 24 hours, and it actually ran better, then it came back on. HELP !!!


Could be the P0445 - Evaporative Emission Control System Purge Control Valve Circuit ShortedThe EVAP canister purge volume control solenoid valve uses a ON/OFF duty\015\012 to control the flow rate of fuel vapor from the EVAP canister. The EVAP ... 2004 Jeep Wrangler
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.3971 seconds