Having problems with your 1991 Ford F150 ?

Trying to replace the gear shift boot on a 1991 Ford F150

\015 Have the boot, the old boot has been taken off. How do we put the replacement boot on?\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 1991 Ford F150

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Trying to replace the gear shift boot on a 1991 Ford F150


... 1991 Ford F150

1997 ford taurus 3.0 ltr trans wont shift into overdrive. first thrugh third gears shift fine but it doesnt try to shift into overdrive at all. the trans shows no signs of slipping and the fluid looks good. I have even tried replacing the shift position modual on the top of the trans and it had no affect. what else might I try?


Solenoid pack in trans. Position module,is just that. Wrong guess. What tran model do you have? You also have other sensors to consider but have to know the trans your working on and the computer and shift stratagy involved to solve this,even if your ... 1997 Ford Taurus

My 1997 Ford F150 wont engage a gear, I had to replace the gear shift cable. Thats installed but know when you shift to revers, neutral or park the shifter just flops up and down with actually going into gear. The truck also will not start, it is if it isn't really in park. What should I check?


... Ford Cars & Trucks

Transmission problem 01 Jeep Grand Cherokee limitied. First had code p1762 and replaced the governor pressure sensor and solenoid. Now drives worse shifting in 1st, 2nd, and 3rd mainly shifting from 2nd to 3rd and now has code p1757 saying Governor Pressure Not Equal to Target at 15-20 PSI and Governor Pressure Above 3 PSI In Gear With 0 MPH. Tried disconnecting the battery to reset computuer and still is doing the same thing. Any Solutions.


I had a shifting problem. The car would start in the wrong gear and shift at wrong times. I repaced the governor postion sensor and tranny fluid and the problem has been fixed for several years. Did you replace the tranny fluid? ... 2001 Jeep Grand Cherokee

Vehicle will not shift from 2-3 gear and so on, it is stuck in 2nd gear, getting ready to replace the main transmission control silinoid . this is a 97 ford f150 any other ideals if that doesn't w


... 1997 Ford F150 Regular Cab

I have a 2005 ford F150. Recently had the transmission fluid drained, flushed, and replace by a garage. Shortly after I noticed that between 45-55 miles an hour when cruising in overdrive that if I press the gas a little more without making it shift out of overdrive that I feel jolts from the tranny. It feels like its trying to decide whether to downshift and the shifting mechism binds or something. I fear that if this continues that I will see increased jolts from the transmission that will


If the wrong fluids were use it could do this and get it replace asap\015\012some ford transmission run on dextron sp\015\012sp= special product exlusif to ford and nothing else will work right\015\012look in your owners manual to v ... Ford F-150

2002 FORD F250 V10-Gas, super duty, 4 wheel drive. Instrument panel out. Altanator not charging system. Replaced Altanator/ check fuses and battery both good. Fixed wire under the boot of the gear shift boot. Checked bulbs on instrument panelall look good. what is wrong? Thanks [email protected]


This definately sounds like a fuse or fuse link has failed..\015\012Don't look at the fuses, check them electrically with a test lamp or multimeter.\015\012And make sure you check both the internal fuse panel AND the fuse panel under the hood.\015\01 ... Ford F-250

91 f150 gear shifter boot replacement


Try the following : " Remove the four screws that mount the shift boot to the floorboard. Pull the boot up out\015\012of the way (It cannot be removed over the shift knob). remove the four bolts that mount the inner shift boot to the\015\012floorbo ... 1981 Ford F 150

What would prevent the clutch from shifting into gear while the truck is running on a 1994 Ford Ranger 2.3? I have tried replacing the clutch master cylinder, slave cylinder and bled the line


It sounds like your clutch is out pull inspection cover off and see if you have any lining left on disk ... 1994 Ford Ranger Supercab

Have a 91 ford f150 and its not shifting correctly. Hard to get into gear if at all, what is it that needs to be replaced? Thanks


... Ford F-150

My 2002 Ford Escape has issues when its cold. When I first start and try to go into reverse is basically wont go. I have learned to park facing out and let it worm up for a while. It will also slip when shifting from 2nd to 3rd. Once the car has run for a bit and is warm all shofting is fine. I dont want to replace. I just put a new tranny in my F150 at 74000 miles costing about 3000 and cant afford this too. HELP!!!


Have the transmission serviced, Change the transmission fluid and filter and have the transmission shop check for any codes and see what the line pressure is at. I fluid could just be dirty and the servos could be sticking due to the dirt. "metal and ... Ford Escape

Hi, I have a 2004 Ford F150 ( new body style ) with a 5.4 L 3V. The problem I've been having and no body seems to know what it could be. The truck idles fine and is not erratic or anything but when I accelerate lightly without pressing the gas to hard ( like trying to save gas ) and it shifts into 2nd gear, it wants to bog down and the rpm's dip a little even while pressing the gas pedal. Then all of a sudden its like it catches up with the amount of pedal I put in and it will throw you back in


The valve on the intake manifold that controls the idle and will speed up when AC is turned on ,i think the problem is here ,its not working right allowing air to by the throttle buttlefly causing the mixture to be out .so when ECU senses that the mi ... 2004 Ford F150

How to replace gear shift knob on 2003 ford f150


... 2003 Ford F150 Regular Cab

My 1989 Ford F150 manual transmission is stuck in reverse, even when the truck is turned off. The day before it grinded / hard shifting into 1st and 2nd gear. The next day it would only go into first if the truck was turned off. After bleeding the line all pressure has been lost from the clutch. Pumping the clutch manually yields nothing in the master clutch cylinder (the fluid doesn't move, ie bubble and yes the fluid is full DOT 3 brake fluid) I am planning on replacing the clutch master cylin


YOU NEED TO PULL THE TRANS AND REPLACE THE SLAVE CYL IF THE FLUID IS LEAKING AT ALL ONE WAY OR THE OTHER YOU WILL END UP REPLACING THE CLUTCH MASTER CYL BUT THIS TIME YOU NEED TO GAIN ACCESS TO THE SLAVE CYL AND APPLY PRESSURE TO IT HOLDING IT BACK W ... 1989 Ford F 150

Have a 1993 ford f150, 5.8. Engine light would come on when idling and would go off when I gave it gas. Now light is staying on and automatic transmission is shifting hard in all gears. Any suggestions? Trying to prevent from having to take it somewhere to be fixed. Did take it to Auto Zone to be tested. Not too sure about reading. was having trouble operating it and thought that it was a trouble code 998 . Thought I might have a vacuum leak due to light going off when giving it gas, but


... 1993 Ford F150 SuperCab

Replaced clutch and noew hard to shift gears - 1996 Ford F150 Regular Cab


May be caused by clutch not fully releasing.\015\012Ensure clutch throw-out clearance is adjusted correctly. ... 1996 Ford F150 Regular Cab

96 ford f150 E40d Transmission, replaced two transmissions, second transmission worked perfect for a few minutes,symtoms are the same as the first transmmission, Drive 2 and Drive are the only forward gears. When placed in drive,it starts out in drive, not Drive 1. Manually shift from Drive 2 to Drive and it shifs into Drive. Both transmissions have P0743 , P0753& P0755 codes.Also changed the computer and wiring harness to transmission


P0743 Torque Converter Clutch Circuit Electrical \015\012P0753 Shift Solenoid A Electrical \015\012P0755 Shift Solenoid B Malfunction\015\012Which computer did you change? ... Ford F-150

My 97 Ford Taurus will not go into park? I have to put in neutral to start. I am trying to find the name of the part under the hood that I need to replace because it is stripped i believe in stead of saying that it is broke. Whatever the part is, when placing it in gear it shifts.


It is called the shift linkage... if your shifter is up by the steering wheel the linkage will be under the hood but sometimes very hard to get to because it can be behind the engine. if it is on the floor then it uses a cable system and the cable co ... 1997 Ford Taurus

1994 ford taurus drives and shifts perfectly when cold. When it warms up[7-8 miles] it won't downshift into first gear. when I try to pull away from a stop it won't move. If I rev the engine it will bang into gear. once it goes into gear it will shift fine through all the gears until i stop again. the hotter it gets, the worse it is trying to get 1rst to engage.


What I am hoping, is that it is the simplest problem, and I will start by asking you ----- when was the last time you had a sevrice performed (transmission fluid replacment and adjustment) ????\015\012\015\012All oils have a viscosity,( r ... Ford Taurus

Shifting gears in a 69 Ford F150 column was moved to floor


Sounds like you got a mistry shifter. It might just be out of ajustment, or just plane wore out. If its an old shifter you would be money a head to buy a new one and put it in. Summit racing sells them, Heck i'am not real sure but you might be able t ... 1997 Ford Expedition

03 Toyota mr2, clutch noise. clutch replaced a year prior. 2 weeks before i heard some noise when shifting. 1 week before it was hard to shift a few times. then one night after driving home i parked and then tried to leave the car was in n. and tried to shift and it just grinded the gears. figured out that if i start the car in gear it would drive. in N. the car does not make any noise. with the clutch completely in the noise i hear is like a sander on a spinning disc. with the clutch in the gra


I hope its your release bearing, but I had this same issue with my Audi and it turned out to be I need a new transmission, the gears are not catching it sounds like. your synchros may also be off. Does it do this in every gear, and once it does move, ... 2002 Toyota MR2 Spyder

2003 Hyundai having trouble shifting into 3rd gear. Manual tranny, clutch replaced 40k miles ago. Recent issues w/air in hydraulic line. Once bled was fine for few months. Tried it again but still having problems w/3rd. Then unable to shift at all and discovered broken bushing on shift arm mechanism. All other gears seem ok? Anyone know how to isolate issues above tranny before I consider replacement? HELP! Thank you.


Most of the time,1st,and second maybe a little hard to shift,if there is a hydraulic problem,but moving,and shifting to 3rd,it is most likely the 3rd gear synchronizer that is the problem,replacement of this item ,would correct the problem.All the pr ... Hyundai Motor 2003 Elantra

I brougt a uses 1999 Dodge Ram 5.9L 4X4. Check engine light came on but then went back out and would not shift to 1st gear when pulling out or manuelly and through information gathered on varies forums, things point to governor pressure sensor and soleniod. I replaced those and still no 1st gear. When again trying to manuelly shift to 1 st gear, I noticed that the shift did not actually engage tranmission. I unhooked the linkage and engaged transmission into 1st gear and it was like the truck w


... 1999 Dodge Ram

Gear shift locks in park and will not move. Had vehicle toured to ford or lincoln dealer 2 times and was told they can not find problem but did get gear shift released by replacing it once but still have similar problems.. Now at home again with same problem. Learned from computer how to release but can not get problem fixed. 8,000 miles remaining on ford extended warranty. Dealer said it can not be fixed.


... 2004 Lincoln Aviator

I have a 1992 chevy 1500 with a 5.7 liter i replaced the ignition control module rotor plugs wires truck would run then backfire and die after it got hot. i unplugged the temperature control module and it ran fine for a day i replaced it and it will idle fine and shift from park to drive gears without dying until its hot. once its hot and i try to shift from park to drive gears it jumps from 200 rpms to 1200 rpms a couple times until it dies.


Please replace your COIL with new one.\012\012Regards, Jay ... 1993 Chevrolet C1500
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.0510 seconds