Having problems with your 1990 Mercedes-Benz E-Class ?

My 1990 mercedes 300ce stalls after driving a few minutes, or will not tart when hot, i replaced the front crank sensor , but have the same problem

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 1990 Mercedes-Benz E-Class

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My 1990 mercedes 300ce stalls after driving a few minutes, or will not tart when hot, i replaced the front crank sensor , but have the same problem


... 1990 Mercedes-Benz E-Class

Engine cranks but wont start when hot,spark ok, injector pulsat ok, fuel pressure 35 to 45 pounds,crank sensor and inginton module was replaced. What can be the problem ? Also replaced mass air flow sensor and idle control motor


I would check the camshaft sensor. ... 1989 Oldsmobile Cutlass Ciera

I have a 1997 chevrolet lumina sedan with a 3.1 engine. had a problem with a loose spark plug wire and replaced a bad throttle position sensor. a few days later the car would run well then not start. replaced fuel pump with used pump. now the pump runs and the engine gets spark and vaccum but will not start unless you spray fuel directly into the intake. the fuel pump will only run when you bypass the fuel pump relay hot to hot. ive been told it maybe a bad cam shaft or crank shaft sensor. does


Then u have no injector operation, check for blown fuses under the hood, look at ECM fuses, there are 2 i believe.. ... 1997 Chevrolet Lumina

I have 1992 Pontiac Bonneville SE with 3800 engine runs good most of time but then it will start to miss and act like it is running on three cyls.,have replaced coil pack,ignition module,crank sensor,computer under dash,throttle body sensor,and vehicle speed sensor and still have problem,it makes no difference hot or cold wet or dry daylight or dark,happens with full tank or half or quater tank of gas and also replaced oil preasure sending unit


Run engine until problem occurs. turn engine off or let it die. leave key on but don't start engine. put a paper clip in diagnostic plug under steering column. look at area on dash where service engine soon flashes. count flashes. (ex. 1flash-1,1 fla ... 1992 Pontiac Bonneville

I have a 1998 Nissa Maxima with 277K+ miles. I bought this car new and it has run great over the years. Recently when turnig the key to start (cold or hot)the engine starts to crank but sometimes "kicks" back or cranking slows down like the battery is the problem. My mechanic first thought the cam and crankshaft position sensors needed to be replaced. We did that but the problem persists. When the engine does start it runs fine at all speeds. My mechanic now suggests the problem is a timing chai


Consider the cost of any work vis a vis the cost of replacing (your pet) bet it works out cheaper to recycle.......( you have to go to switzerland for euthenasia,wonder where cars go.....?) ... 1996 Nissan Maxima

Engine Performance problem 1993 Pontiac Grand Am 4 cyl Front Wheel Drive Automatic Engine dies when dropped back to idle. I replaced the idle air control valve. I replaced the crank shaft position sensor. I have removed and cleaned the throttle body. It's a 2.3 L Quad-4 engine. None of that has changed or corrected the problem. I don't know where to go from here.


Clean the Mass Flow sensor. It is probably a black module with wires on the side of the throttle body. There are a few ways to do this, but I suggest buying a can of spray designed for this purpose from your local parts store (electrical spray or ... 1993 Pontiac Grand Am

2002 Chevy S10 ZR2..... I have a problem with the front brakes and rims getting sizzeling hot after driving for 10 minutes. I've spent about $ 700 at a shop that didn't fix the problem. I've personally replaced the driver side caliper, master cylinder, brakepads, rubber brake hoses both front hub assemblies with new ABS sensors and flushes the brake lines numorous times. I don't know what elso to do. Can you help me? Krazysam USMC VET


... 2000 Chevrolet Blazer

Have code p1391 and p0340, replaced both sensors and still have same problem. lots of backfiring and hesitation and raw gas out the tail pipe. Put oscilloscope on crank and cam sensor signals. loosing crank signal intermittently tried another sensor from dodge and still have same problem. replaced sensor plate in between flywheel and engine crank. Still have same code and problem. Took reading on sensor wire on the sensor itself before the connector to the engine harness. Still loosing signal. 5


Had similar problem with 99 ram. i made holes in crank sensor a bit bigger,removed rubber seal that sensor goes through in trans,installed 1 bolt and adjusted sensor back towards firewall and tightened that 1 bolt and its worked fine ever since ... Dodge Dakota

I have 02 pontiac grand am and it wont start, it cranks over and getting spark and getting fuel, I replaced crank sensor, however i pulled spark plugs and didnt smell gas in the cylinders when someone else was cranking it with the key. not sure if fuel rail is bad or if the computer isnt letting the fuel into cylinders. the fuel rail is getting fuel cause i checked the release pressure valve like on a tire which is located on front side of motor. what is my problem?


Attempt to start the car by turning the key to the Start/Run Position. Observe that the vehicle fails to start and that the security light is illuminated. leave the key in the 'ON/Accessory' Position. (DO NOT turn key to the 'off' position.) ... 2002 Pontiac Grand Am

Liberty 3.7l, stalled and would restart. Has had new cam and crank sensor. Was checking crank sensor and ASD fuse blew. Replaced fuse and continued to crank ove, smelled something hot, found #3 coil was smoking, removed coil (it melted) and replaced. cranked over and new coil is too hot to touch. Also checked spart plugs, looks like it is time to replace them .065in gap. Why won't this thing start?


Well, some things need to be done systematically. Check for spark to make sure the coils are in fact working. Check for fuel to make sure you don't have a bum fuel pump and/or plugged filter. Ignition coils will get hot. The very fact that it melted ... 2002 Jeep Liberty

If i hooked a hot wire with a switch up to my dual radiator fans with a switch, would that affect my 1998 dodge neon, 2.0 L, manual transmission, dohc to have a problem dying? I have replaced the cam, crank sensor, fuel pump, alternator, coil pack, plug wires, radiator. I replaced the engine a year ago. The only thing that I can think is that the PCM is bad. How can I check the PCM out to see if it is bad.


It shouldnt affect anything ,b ut if engine keeps dying then thats another problem ... 1998 Dodge Neon

My 95 318ti runs fine when you start it. Then when driving and warm it dies. You can restart it and move the car briefly before it die again. When it cools down it runs again fine until hot. The auto trans has been replaced, the alternator, tune up done, crank sensor replaced. Two mechanics are stumped. Both computers have been switched out, bu the problem has not gone away. Good car that won't run. Any ideas. Could the failing alternator have messed up some other part of the electronic


HI! It may not be the sensors nor the alternator. I suspect a faulty water pump and a clogging radiator in the car. If its bad, the water wont circulate and may cause your engine to be hot enough to shut itself off. Have it replaced to get your car c ... 1997 BMW 318

Replaced the 2 O2 sensors in front of engine. was wired wrong because dealer that i got car from years ago cut from engine harness, timing belt broke replaced it and the water pump. car started to over heat and would not stay running. took it in to the dodge dealership and got it to crank and stay running but the over heating problem is still there. is this a bad or cracked head or is it something simple that im not doing right. it runs fine just over heats after about 15 to 20 mins of running.


Is the electric fan coming on?if not it will do exactly what you describe.\015\012once in a while at a steady 40mph speed,it may cool down.\015\012there is a fan switch on the radiator that drives a fan relay.\015\012you can wire 12 ... 2001 Dodge Stratus

I have a 98 wrangler 6 cyl. automatic. When I start it, it revs high, hot or cold, and if I give it gas it pops through the exhaust. I just installed a new engine, cap rotor, plugs, wires, crank sensor, cam sensor, fuel pump. ahd this problem prior to engine replacement. could the IAC cause the mis fire? i am getting a p1390 and p0320 code. could it be a intake leak? not usre what is causing the popping...


P1390 Timing Belt Skipped One Tooth or More (Chrysler, Jeep, Mitsubishi)Easy way to clear codes is to just disconnect the battery for about half an hour. Chances are though for that code to show up it actually is out of sync. Clear the co ... 1998 Jeep Wrangler

I have a 9000 2.3 CSE turbo bought new in 1995. the immobilizer was fitted to the car before i picked it up. my problem seems to be the fob which is a unit that hangs around with the ignition key. ( not the fob battery operated type) when cool it starts no problem,when hot it has started to play at turning over but not starting. I have replaced the battery. had the crank sensor changed, but it still plays up. However today and yesterday, I noticed that if it does not fire up first time, the


... 1994 Saab 9000

Buick Lesabre keeps cutting off. the crank sensors was replaced, and now the mechanic says that it needs to go to the muffler shop. the car has exhaust problems. Can a car exhaust getting hot cause the sensors to stop working?


... 1995 Buick LeSabre

2007 s550 cranks but doesn't turn on when vehicle is hot I replaced the crankshaft sensor and cam shaft sensor and still having the same problem I have no engine light


... 2007 Mercedes-Benz S550 Sedan

I have a 2006 jetta 2.5 and the epc light came on and I took it to the dealership to have it repaired. The very next day the car started doing the same thing. They replaced the crank sensor. When i took it back the second time they replaced the same exact sensor again the next day the car started doing the same exact thing. Im assuming the crank sensor is not the problem. Have anybody had this problem before and if so did u find a answer to fix the problem?


... 2006 Volkswagen Jetta

I have a 1998 dodge ram 5.9 liter truck cranks over but wont fire replaced a crank sensor truck fired but acted as it was bogged down with fuel so replaced the map sensor fixed the problem truck ran great drove it a few miles and parked it for the next day went out to start the truck she cranked over but wont fire she has fuel and spark but seems to back fire through intake manifold whts the problem


... 1998 Dodge Ram 1500 4WD

My 2006 F150 abs light would come on after driving it for a few miles. I changed the rear sensor and it still didn't correct the problem. I had the brake pads replaced and cleaned the front sensors. I had an error code on the front right sensor and after having the pads replaced and the code check again, the error code was gone. I drove it for a little longer period of time and the abs came back on. Is there any other solution you might have to correct the problem with my abs light. Than


It sounds like you might be having a problem with your Electronic control module. Are the only codes coming up just for the sensor? Have you recently cleaned your engine or driven in very wet weather? If so, water could have gotten into your conne ... Ford F-150

Wont Start I have replace the crank shaft sensor, plugs, and i get spark. When I turn the key, the starter will come on, but it will not turn over. I took it to a mechanic, who was the one that replaced the crank shaft sensor, and his diagnosis showed a couple of cyclinders misfiring. After the crank shaft sensor was replaced, the jeep ran all day. I turned it on and off a couple of times throughout the day. However after running it for an hour and a half, I stopped to get gas, and the problem r


It could be the pigtail {harness} that plugs into the crank sensor. ... 1999 Jeep Cherokee

Overheating Thanks i replaced the crank sensor and it started right up!!! Now im having an overheating problem it has new radiator, hoses, thermostat, and water pump.. but gages and smell says its getting hot.. but to the touch on cap its cold.


When you fill the radiator does it accept coolant easily or do you need to pour it in little by little? If It dosent fill easily I'd suspect a partially plugged radiator. Also, make sure you have the belt routed correctly. It is possible to get drive ... 1995 Jeep Grand Cherokee

The front passenger ac is blowing hot air on my 2008 Yukon. What might be the problem and price? Also, the check engine light and came on and off for a week. Is this related? We've had the fuel sensor replaced last year.


... 2000 GMC Yukon

1996 - often stalls shortly after hot start, then have to wait for engine to cool down before it will restart. Otherwise car runs very good. Note - replacing crank sensor did not fix this problem. Thank you!


Check for the radiator........it should not be choked and also the pipe lines...........check weather the radiator fan is working or not ... Chevrolet Cavalier

Ignition problems 88 oldsmobile it starts and runs good for a while once the engine gets hot and you turn it off it will crank but wont start.starter,starter relay have been replaced but does same thing.engine model is a 3.8 front wheel drive.


Maybe the crankshaft senor that happened to mine it was cracked almost in half ... 1988 Oldsmobile Cutlass Ciera
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.7814 seconds