Having problems with your 1990 Dodge Grand Caravan ?

I am trying to remove a crankshaft bolt from a lexus i300 is it a left or right hand thread

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Is right hand thread
Repair Help & Product Troubleshooting for 1990 Dodge Grand Caravan

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am trying to remove a crankshaft bolt from a lexus i300 is it a left or right hand thread


Is right hand thread ... 1990 Dodge Grand Caravan

Crankshaft pully bolt is left hand thread or right hand thread when removing for cam belt replacement honda accord 1995 and how do you lock bottom pully ,due car being automatic


... 1995 Honda Accord

Working on a 1998 Dodge Caravan2.4 4cyl engine. Have removed notor mount power steering pomp, inner splash shield,. dont know how to remove outer bottom belt shield. the directions i got from auto zone did not say anything about removing the crankshaft pulley. but the shield is not slotted only way to renove is torenove the pulley. Is this correct , is the bolt right or left hand thread, i have attenptedto loosen with no luck. please advise on how to procede and what steps to finish disassenbly.


... 1999 Dodge Caravan

L200 ON A 2003 PLATE TRYING TO REMOVE CRANKSHAFT BOLT AS NEED TO REMOVE PLASTIC COVERS TO CHANGE BELTS IS IT A LEFT HAND THREAD ASCANT UNDO ?


... Mitsubishi Pickup

IS THE BOLT ON THE CRANKSHAFT PULLY RIGHT OR LEFT HAND THREAD?


... 1992 Honda Accord

2002 Saturn SL2 crankshaft bolt removal - right or left handed threads?


Look at rotation of harmonic balencer to remove bolt is in opposite direction.To remove bolt :Disconnect coil wire or wires so car will not start Next put socket on bolt with breaker bar and wedge bar some where solid on car. Bump motor with starter ... 2002 Saturn Sl

To remove crankshaft harminic ballance lock bolt is it left or right hand thread Glen.


Anti clockwise when facing the engine !\015\012Its will be very tight so fit a socket with a braker bar & rest it on the chassis rail the clck starter [on & offf quickly] but make sure it cxant hit anything else!!! \015\012Cheers ... 1993 Isuzu Rodeo

2007 Volkswagen Jetta rear axle bolt. Trying to replace the wheel bearing but can't get the bolt to break loose. Have the 12 point 18mm tool but not sure if the bolt is right handed or left handed threads.


... Cars & Trucks

Idler pulley retaining bolt on a 2006 honda accord v6 serpentine belt assembly right hand thereaded or left hand threaded?


... 2006 Honda Accord

Crankshaft thread can you please tell me if the crankshaft bolt is a left or right hand thread on 1994 mitsubishi galant 2lt v6rn Thankyou graeme


Right hand thread ... 1994 Mitsubishi Galant

On a 1996 pontiac sunfire gt with 2.4 l engine is the crankshaft pulley bolt right-handed threads or left handed threads


There's nothing mentioned in the repair section that the bolt is not standard right hand thread. You could check with a GM dealer to make sure. ... Cars & Trucks

I am trying to replace a rear wheel bearing in my 2001 audi quattro base model 2.8. I am having difficulty remove the hub bolt it is now stripped i am curious if it is left hand thread or standard thread because it will determine if I drill and tap a bolt in or use an easy out.


Had the same problem with mine, except i didn't strip my drive axel bolt. It is left loosey!!! LOL I took a propane torch to mine for about 3 - 5 minutes. Then i stood on the wrench, literally! ... 2001 Audi A4

I have a1993 Geo Storm, 1.6L engine, having problem getting the bolt on the crankshaft pulley loose. Is it a left hand thread or a right hand thread.


The crankshaft pulley bolt loosens by turning Counter-Clockwise. Ensure the pulley is secure from movement so that you can loosen the pulley bolt without turning over the engine. You may need to use breaker bar to loosen the pulley bolt, or at least ... 1993 Geo Storm

The driver's side caliper bolts will not loosen up. My sucket wrench broke in the process of trying and I can see one of the bolts head is starting to strip. What can I do? Could it be left handed thread? The passenger side gave no troubles at all and they are right handed.


No, all threads are right handed. Can you take the whole bracket off the hub to get a better angle? Can you push back the boot and get a vice grip on the bolt? If it comes down to it, you'll have to drill the bolt out. ... Chevrolet Venture

I Have a 2000 Mazda protege 1.6 and i need to know if the crankshaft pulley bolt is a right or left handed thread. Ii dont want to break to tip off crankshaft ive done that before it sucks


It is "lefty loosy" ... 2000 Mazda Protege

Have 1994 ford ranger xl and need to replace right rear axle & backing plate. cant get small bolt out of 3rd member that holds in pin for spider gears so axle can be slid in and keeper removed, its now stripped, how do i get it out and is it left or right hand threads ?


IT IS RIGHT HAND THREAD, HARDENED, WITH LOCTITE FROM THE FACTORY. LOTS OF HEAT AND A VERY GOOD SET OF VICE GRIPS. GET IT RED HOT THEN CLAMP THE VICE GRIPS ON THEN TAP V/G WITH HAMMER TRYING TO BREAH THE LOCTITE FREE.ONCE YOU GET THAT LOCTITE BROKEN I ... 1994 Ford Ranger Supercab

Hi i need to know how to get the bottom fan belt pulleys off the crank so i can change the timing belt, is it a left hand thred or right hand thred and how can i stop the engine turning when i try to remove the bolt. its a 1989 mazda b 2200 ute


The bolt loosens by turning counter-clockwise. I have used a chain strap wrench (from a tool place, such as Harbor Freight) to hold the pulley to loosen. A heavy duty impact gun is the best bet, but not having one and a compressor, makes that not pos ... Mazda B2200

Which way is the thread on the bolt that holds the crankshaft pulley on a 1994 camera. Is it left hand or right hand


Lefty loosy righty tighty. It's normal thread but not fun to get off. Good luck. ... Toyota Camry

Is the bolt on the crankshaft pully right or left hand threads?


The crank pulley bolt on most Honda engines are very difficult to loosen. Most 1/2" impact guns are just are not strong enough to loosen them. The choice is yours to either use a 3/4" impact gun, the bolt is left losey, righty ... 2002 Honda Odyssey

Working on Honda Prelude 1992 with a 2.2 motor can't get bolt off crankshaft pulley wanting to know if it is left or right handed threads


It is standard thread (right handed) and a little more information if you need it: there is a hole on the rear of the block on the drivers side located just behind the rear balance shaft so you can lock your engine #1 cylinder @ TDC with a 6mmX100mm ... 1992 Honda Prelude

Crankshaft pulley bolt on a 2000 Nissan X-terra 3.3 liter V-6, left or right hand thread?


U turn counter clockwise to loosen, but you MUST USE a good quality air impact gun to get it loose. ... Nissan Xterra

Is the crankshaft bolt thread right or left handed on the Honda Oddyessy RA1?


... 1995 Honda Odyssey

Tension pulley i'm trying to change the idler/tension pulley....is this a right or left handed thread ? i can't seem to get the old bolt to turn and i don't want to snao it off.


It's a normal bolt, righty tighty lefty loosey. Try some DB Blaster and let it soak. Another thick is to tap the head of the bolt from side to sid ... 1992 Ford F150 SuperCab

How do you remove the front crank shaft pully from a 2003 Hyundai Elantra GT? How do you get the bolt out of the crank shaft pully? Is it right or left handed threads?


It undoes normal way but its tight as its a taper end on crank and no keyway so dont hammer it off with the starter motor and a big bar locked into the suspension.You will have to use a special tool to lock the crank in position ,the other way i do ... Hyundai Motor 2003 Elantra

Just need to know the thread direction on the power steering pump pully for my 91 rodeo with the 3.1 V6 and the GM Saginaw pump. Just trying to figure out if it turns clockwise (to the right) or counterclockwises (to the left), to remove the bolt.


The pulley isn't threaded on - it's pressed on. You will need to buy/rent a pulley puller/installer. Any O'Reilly's or NAPA should have what you need!\015\012\015\012\015\012Hope this helps - KC GTO Dad ... 1991 Isuzu Rodeo
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.3097 seconds