Having problems with your 1988 Ford Mustang ?

What size tool is needed to replace the seatbelts in the front on 1988 Mustang LX Hatchback?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 1988 Ford Mustang

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What size tool is needed to replace the seatbelts in the front on 1988 Mustang LX Hatchback?


... 1988 Ford Mustang

What tools will i need to replace my brake pads on a 2000 silverado 1500 ? I was told i will need a torx bit for the front. What size and what do i need for the rear ?


Should be like a 3/8 allen wrench but if it is a torx should be a t45-t50 ... 2000 Chevrolet Silverado

REPLACING FRONT STRUT ON MY 2000 ALERO,wHAT SIZE TOOLS DO I NEED TO REMOVE& REPLACE NEW STRUT.


... 2000 Oldsmobile Alero

How to replace front wheel bearings on a 2005 sunfire,and what tools and size of sockets do I need?


First lift and support the car, than remove the tire.Now the fun begins first you will need to have a 3/8in.or so allen wrench to remove the caliper next you may or may not need to remove the caliper hold down bracket if so you will need a 13 to 15 m ... Pontiac Sunfire

I need to replace the front rotors on my 1990 full size Bronco 4x4. What is the correct procedure? Are any special tools required?


... 1990 Ford Bronco

I need to change my front and back shocks on my 1999 chevy blazer 4.3 4x4 and the bolts are pretty rusted so I want to go out and buy some new one's before I replace the old shocks in case I bust one, and I don't have an owner's manual to tell me what size of bolts I need to buy to do this. So could you to me what size I would need to get for the front and back shocks?


If you call the dealer they may tell you the bolt size or they would get them for you. Probably wouldn't be too expensive and you would have the right size and grade. ... 1999 Chevrolet Blazer

Brake how can i replace my front brakes? what the tool do i need and is there any special tools do i need to replace my brake pads on my 98 grand am 3100


Gm uses one of 3 tools to remove calipers 1- T-50 tork bit 2 3/8 hex scoket 3 13mm socket ... 1998 Pontiac Grand Am

I lost my owner manual for my 2001 XLT ford Expidition and I need to replace a fuse for its front head lamps. Can someone email me a fuse box layout. I need to determine the size and the front head lamp fuse location so the fuse can be replace. My email: [email protected] Thanks, James.


I was able to download a new manual from the Ford website in pdf format. ... 2001 Ford Expedition

Need to know how to remove the bearings on the front spindles on a 4 WD 1985 dodge truck 250 3500lb front axles. they look like they should just slide out since i removed the gasket but they do not. I replaced the U joints and thought I should go ahead and replace bearings and oil seals(done with oil seals). I have tried prying them out but they are in there pretty good, didnt know if someone had a trick i could use or is there a special tool one needs. Thanks Billy


... 1985 Dodge Pickup 4WD

I have just purchased a replacement hub for my 2003 Ram 1500. There are no instructions on how to remove & replace the hub. The Ram has ABS. I"m also going to replace the front brake pads on both front wheels. I know how to replace the pads but I'm wondering if I need special tools for removal of the Hub.


The best way for me to walk you through this is to have you watch a video because it's a lot of typing and might not make much sense if you were reading it. Check it out here: ... Dodge Ram 1500

I am replacing an oil pan for a 2005 Hyundai tuscon. need to know the bolt size of the pan bolts - 12 to 14 of them. what size bolts connect the front exhaust manifold bracket to the 'y' pipe? what size bolts hold the rear exhaust pipe to the 'y' pipe? need to disconnect both to get at the pan bolts. thanks tom


... 2005 Hyundai Tucson

I have a 1997 Plymouth Voyager with a 3.0L engine. I am trying to replace the oil pan gasket. The literature says I need to remove the front motor mount bracket, bending braces and torque converter dust shield in order to remove the oil pan. It seems the brackets and braces use a strangely sized socket. I am also worried about having the engine fall on me when these brackets and braces are removed. What size of sockets do I need to use and where can I find them? Do I need to support the en


... 1997 Plymouth Voyager

I need to remove the front brake rotors from my 94 Isuzu trooper to either turn or replace them. Is this a complex project requiring special tools to remove or re-install due to the auto 4wd hubs? I have removed, re-packed and replaced rear wheel bearings before, but never fronts or messed with 4wd hubs.


... Isuzu Trooper

I have a 1989 jeep cherokee that has a roaring noise in the right front. it sounds like a wheel bearron and or u joint going bad. is it very difficult to change and do I need specal tools to replace the wheel baerron and u joints. I have replaced the rear main oil seal without pulling the trans or droping the front end, which all the information said I whould have to do one or the other. Can you help?


Sounds like a wheel bearing,to check jack it up on that wheel then from top to bottom grab the tire and then try to move it up and down like your trying to pull it off if it moves alot its bad.no it doesnt take any special tools but it is difficult t ... 1989 Jeep Cherokee

I want to replace the front brake pads and rotors on a 2006 Ford Escape, V-6, 4 wheel drive, not hybrid. What size allen wrench will I need to remove the calipers? And what size socket will I need to remove the rotor?


... 2006 Ford Escape

I need to replace a rusted brake line that goes from the front to the rear brakes under the drivers side. What I need to know is the size of the tubing and the size of the threaded ends. this is for a 92 geo prism. thanks Rich


... 1992 Geo Prizm

I have a thumping noise from the front driver side wheel. I replaced rotors,rebalanced and rotated tires. I'm thinking bad front bearing. How difficult is it to replace. I hace auto skills and all tools needed.


A bearing has a more constant growl. Thumping is more likely a CV joint issue, Inspect the drive shafts... ... 1997 Toyota Camry

Need to replace passenger side front fender. I have new front fender, it is painted and ready to be installed. Are there any special problems or tools needed?


Just used standard sockets with extenson, screw driver and phillips, remove head light and fender and fender guard cover. helper would really come in handy, so you dont scratch or drop fender. ... 2000 Ford Taurus

What size wrenches are needed to replace front and back brakes 02 chevy silverado LS 1500 2WD? do the fronts and backs require different size wrenches?


Do your self an immense favor and go to an auto parts store and pick up a service manual either by Chilton or Haynes. These manuals have a wealth of information including torque values for anything you bolt back together. Most will show you all the ... 2002 Chevrolet Silverado 1500

Im trying to do my front brakes and I need to know the size of the torque bit to release the caliber to do the brakes I have all the other tools I just dont know what the size of the bit I need is


Most of them use a T65. ... Pontiac G6

How do I get more info? I need to know if there's somewhere I can get a picture of this area? What tools do I need to get into the area? do I remove the star shaped thingies on the metal plate near the latch? What size spring do I need? Where would I get it-- hardware store? dealer? If dealer, what's the part number?? thanks. Gale This is about a Jeep Grand cherokee, 1998 with a broken latch for the lift gate. I already got the answer that I need to replace the spring, but no info on what siz


Hi gale\015\012im joel\015\012\015\012let me just jump into this one really quick.\015\012\015\012the best thing to do is to not get any parts for your car from the hardware store.\015\012to replace the handle. ... Jeep Grand Cherokee

What size tools do i need to take of front caliper


What kind of car first of all...and I would guess u are gonna need something in metric since most new cars are metric sizes. if metric doesn't seem to fit then try american sizes..and just to make sure in case a ratchet and socket can't do it ..then ... 1999 Volkswagen New Jetta

What tools do I need to replace front brakes


Metric sockets and a 6" C clamp ... 2005 Kia Rio

What tool do i need to replace front brake pads on 2008 mariner?


You Will Need A 13-14 mm Wrench for Caliper Bolts .A Large Flathead Screwdriver to Spred open Caliper/Shoes to Remove Caliper from Rotor,\015\012After rhis you Can use a LARGE "C" Clamp to CLOSE Caliper Piston. ... 2005 Mercury Mariner

What tools do i need to replace front caliper?


What type of car? most all tools needed are 10-14mm wrenches or some alen wrenches or sometimes a t set is needed also a C clamp to push in the piston ... 1992 Ford Taurus
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.0931 seconds