Having problems with your 1987 Dodge Ram 50 ?

Engine Dies After running for about 10 min. engine dies. It will turn over but wont start for a while. Replaced fuel pump and ignition coil still same!!

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Check fuel filters and check fuel lines
Check vent line from tank to fuel filter or canister or gas line , get air compresser and blow both lines out towards gas tank having one personstand by tank with gas cap off listening for thump sound or gushing air
Repair Help & Product Troubleshooting for 1987 Dodge Ram 50

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

91 plymouth grand voyager dies when it warms up to operating temperature then starts and runs normally after cooling a little while. Replaced fuel filter and coil. Fuel still has pressure after it dies so fuel pump is working. This model has no pickup coil and ignition module appears to be in Engine control module. Is timing picked up by crackshaft sensor? What is the most likely culprit. Engine control module is $179.00 so would like to exhaust all other possibilties first.


Possibly the coolant temperature sensor is faulty , Please give a check to it then go for replacing the engine control module. ... 1991 Plymouth Grand Voyager

91 plymouth grand voyager dies when it warms up to operating temperature then starts and runs normally after cooling a little while. Replaced fuel filter and coil. Fuel still has pressure after it dies so fuel pump is working. This model has no pickup coil and ignition module appears to be in Engine control module. Is timing picked up by crackshaft sensor? What is the most likely culprit. Engine control module is $179.00 so would like to exhaust all other possibilties first. Coolant sensor must


Timing is picked up by camshaft sensor. If you don't have one then crank sensor. 02 sensor control air/fuel lean/rich mixtures. Plugged catalytic or muffler would cause this. Bad temps sensor will also cause this. ... 1991 Plymouth Grand Voyager

Engine Dies After running for about 10 min. engine dies. It will turn over but wont start for a while. Replaced fuel pump and ignition coil still same!!


Check fuel filters and check fuel lines ... 1987 Dodge Ram 50

I have a 1990 jeep wrangler 2.5l with fuel injection. I have replaced computer and ignition coil, still will not crank. the Ignition coil is reading 1.5ohms I have no pulse either. what is the promblem? fuel pump is working fine. engine runs when fuel falls into it when changing ignition coil. after initial fire runs no more. something is preventing the ignition coil to activate. I have 12 volts on hot side but find no ground which runs to the computer. why would the computer not be giving


The best idea is to pull out all Diagnostic Trouble Codes (DTC) from Engine Control Module (ECM). Trouble codes can be displayed by the Malfunction Indicator Lamp (MIL) or by using diagnostic equipment connected to the data link connector (DLC) of ... 1990 Jeep Wrangler

I just bought a 2000 dakota with a 3.9 v6 engine it runs great at a constant speed for 6 or 7 miles then it starts acting like its not getting enough fuel sometimes it will actually die. I was told that the fuel pump had been replaced. when I had the codes there was a misfire problem so I have replace the plugs, wires, cap, rotor bug and the coil as well. Now the codes are still saying that there is a misfire but also a high low fuel pressure. So do I need to try replacing the fuel pump or is th


Just a quickie ,try it with the fuel cap off ?? ... 1989 Dodge Dakota 2WD

I have a 1983 Dodge ramcharger, I have let it run till it shuts off several times to see what is HOT after it dies out and still have not figured this one out? Nothing feels that hot? Obviously, :/ I too have replaced the norm that would cause this shutting off after 15 minutes or so of running? I have replaced fuel pump TWICE!,fuel filter TWICE,ignition coil,pick up coil,rotor,cap,wires,plugs,dimmer switch,carb rebuild kit,Voltage regulator,Ignition control modulator,Balaster resister,oil chang


Have you replaced the condinsor ... 1983 Dodge Ramcharger

Honda accord 1993 car was running on the freeway 101 and the car start to slow down and die. during troubleshooting new battery installed,replace ignitor and all 4 spark plugs has ignition. the car still wont start. just crank but will not turn over. check the fuel line with ignition on and fuel comes out normal. so the fuel pump works. we even spray fuel starter in the intake and pass to butterfly to be able to turn it over the engine but engine just crank. wont turn over. what is wrong. why th


Hello! I need to understand the problem...Just a couple of questions to get started...When you say that you changed the igniter, do you mean the ignition coil? Have you checked for spark (hold plug to ground)...If there is a strong spark and fuel, th ... Honda Accord

2000 saturn LS1...ignition seems to be locked up. Battery functions, as well as the fuel pump, ignition coil, replaced the starter and crank sensor, and timing gears chain and water pump were all replaced by the dealership a year ago...still engine isnt turning over ... any ideas at all as to what i might try next?!


Check power to starter motor and solenoid. If no power present on engine crank, then check ignition barrel, key and main fuses.If power present on cranking, but starter motor does not energize, then check starter connections and replace starter motor ... Cars & Trucks

I have a Ford F150 5.0L 2 Wheel Dr. The engine would turn and acts like it will run but it fails. I replaced the fuel filter and checked the pumps and it is working and supplying fuel to the engine. I have also check one of the spark plug and it has a spark. I replaced the coil and its still not working. I have heard about "IGNITION MODULE" but I'm not sure where it is located at. I'm not even sure if this is the problem. Please help! Thanks.


Check and see if there is a white ballast resistor between the ignittion module and the hot wire the resistor would go out and as long as you cranked on it it would act like it was trying to start and when you quit cranking on it it would die. ... 1989 Ford F 150

2001 Town & Country. No spark. Have codes 0351, 0352, 0353, 1193. Checked coil pack wire harness. With engine ignition in the starting mode 9.85 volts. Replaced coil pack and crank sensor, still no spark. Fuel line has pressure and I can hear fuel pump when I turn on ignition. Confused and considering getting rid of van, Help!


Hello and welcome to FixYa!\015\012\015\012As a first course of action, I strongly suggest that you remove the positive battery connector and let it sit for atleast 5mins. before reconnecting. This will reset the system and may get it back to i ... 2001 Chrysler Town & Country

I have a 1988 Isuzu Trooper II 2.6L MFI engine. I was 3 blocks from my house when suddenly the engine quits. It would turn over and die each and every time I tried to restart. I have done the following to try and resolve to no avail. Ignition Switch Coil all fuses---tested or replaced relays---fuel pump and engine checked sparked at #1 plug-OK fuel rail---OK I forgot, the ONLY way I got the truck home was to hold the key all the way to the right like I was starting it. I held it in t


I can suggest a sort of thumb rule in such situations. Spray some carb cleaner into the intake after repeating it twice even if can feel a change in the sound as if its about to start then I suggest you add some carb cleaner to the fuel itself, at th ... Isuzu Trooper

Own a Mazda B2600I, 2.6l. The brake lights+tail lights stopped working, and fuse kept blowing. Then the truck died as a was driving down the road. Replaced fuel pump since it didn't seem to be pumping, still wouldn't start from crank. Don't have spark on plugs (thought it was from all the starter gas I had tried) but distributor turns. About to try replacing ignition control module because it has power on off position but none during on/cranking engine. Anyone have other ideas or experience?


... Cars & Trucks

Hi any ideas have audi 200 q turbo 1986 will not start? no spark at plugs engine management light came on for a few months and slowed car down but now will not start. replaced ecu. ignition switch, new coil and transistor, distributor cap,rotor arm. new fuel pump relay, but with no luck still have now taken off ignition timing sensor, and engine speed sensor both look identical and have the same part number? does anyone know are these the same.? knock sensor removed. any advice would be great. r


It could possibly be your timing belt. If it broke then the rotor won't spin and no spark will be produced. ... Audi 200

I have a 1988 chevy suburban. I recently replaced the fuel pump, filter, coil, ignition module, cap and rotor, plugs and wires. Engine will start and run for 5 to 15 seconds then die and will not restart. After a couple days will repeat proses. Getting fuel when cranking engine, but no spark. Any suggestions would be appreciated Thanks Seth


You see fuel coming out of the injectors or you have fuel pressure? ... Cars & Trucks

My 97 Acura CL 3.0liter stopped turning over. Pulled the starter and solenoid had it tested, was ok. Pulled the distributor and changed the ignition control module still no cranking of the starter. Replaced the ignition electrical part, still no crank. The engine light comes on then turns off and the relays click, the fuel pump makes noise as it should. Pulled the coil and tested it. Has same resistance as a new unit. What else is there? I know its not the Neutral switch because the key only act


Sounds as though you changed parts unrelated to the engine turning over. The ign module etc would be where you would check, if you had no spark.\015\012Do you really know that the ignition switch is okey\015\012Do you know that the neutra ... 1997 Acura CL

2000 Jeep Grand cherokee Laredo wont start. Engine turn over . No noise from fuel pump with ignition on. Replaced fuel pump and filter.Turn ignition on- pump did not run.Jumped the fuel pump at the pump relay.Pump worked and pressurized fuel rail. Still no start. Checked OSD relay and fuel pump relays and fuses-all good. I noticed that the fuel guages were malfunctioning. Battery guage hardly moves.Battery full . The anti theft light stays on as I tried to start engine.


Sounds alot the the pcm it controls the fuel pump and ign system but the anti theft would keep it from starting because the key has a transponder in it programmed for that vehicle and that would kill all ign if triggered ... 2000 Jeep Grand Cherokee

Fuel problem i put in ignition coils today on 2000 kia sephia and also replaced the fuel filter the pump is running and i am still not getting any fuel possibly a bad fuel filter because after i replaced the ignition coils it would run for 10 seconds or so then cut off which lead me to the fuel filter which was really dirty so bought a new one and now it still wont stay running.


Is there muck in tank\015\012take filter of and tip contents into jar\015\012and see if clean ... 2000 Kia Sephia

Mine Isuzu's Troopers details as below :- year : 1993,model : UBS55 Prob : While driving around 50km on mileage, suddenlly engine do jerking and will stop. I already do replace my oil filter, AC Pump, Ignition coil, ignition cable and spark plug. but this problem still happen. It's looks like fuel can't reach at the carburator but in idle situation its goin smooth and nothin happen but if I take a ride for at least 50km above the problem will appear when I shifted to max gear.....hope u guys c


... 1993 Isuzu Trooper

I have a 1986 zuki samurai and have had it for about 3 months and it has ran like a top but two days ago i was driving it and it just died and would not start back i checked the fuel pump it is working fine i have replaced the ignition coil the distributor cap the rotor button the plugs and the wires and it is getting fire to the plugs but it will still not start the night it died i tried rolling it off and popping the clutch and that wouldnt work either im just curious if anyone else has had a


Sounds like the timing belt has broke but without a look ? head under the bonnet and kick up the exhaust i honestly couldnt say please ask a local mechanic to have a look for you ... 1986 Suzuki Samurai

1995 olds 88 3.8 L. Sometimes won,t start.Cranks and immediatly dies on 1 to 10 attempts.Once starts ,runs fine. already replaced crank pos. sensor. Can hear fuel pump prime up when key is on. No check engine lite coming on. There is fuel pressure at rail. I have disconnected mass air flow sensor to see if it would start, it would not. Ignition module & 3 ea coils were removed and tested good.


... Oldsmobile Delta 88

Electrical My 1989 porsche 930 Turbo has a very unique problem. When I shut the engine off, even take out the key, it keeps running. I have only been able to shut engine off by pulling coil wire. Mechanics have been through wiring and replace the delay relay but still no fix. yesterday it was sitting in the parking lot totally turned off then all of sudden the red idiot lights in dash come on and fuel pumps start buzzing, just as if you put the key in and turned ignition on. Any ideas?


Your help was of no value, the technician had never seen the inside of a Porsche. thanks anyway ... 1989 Porsche 911 Turbo

I HAVE A 2001 AUDI A6 2.8 IT WAS HIT HIGH IN THE FRONT AND BROKE COIL AND IGNITER I REPLACED BOTH BUT I AM NOT GETTING FIRE I AM GETTING INJECTOR PULSE I REPLACED THE FUEL PUMP RELAY AND THE POWER SUPPLY RELAY AND STILL NO FIRE THE IMOILISER LIGHT COMES ON BUT GOES OFF WHEN TRING TO START CAR ENGINE TURNS OVER FINE


Check for power at the coil. Maybe a ground come lose to the coil id check all my wiring. ... Audi A6

My trucks fuel pump when out while i was waiting on cash to get a new pump i left my door ajar and the battery went dead 3 ot 4 days later I installed the new fuel pump then realized my battery was dead. Replace my battery and couldn't get it to start (no spark). I replaced the ignition coil distributer cap rotar cap still no spark. Then I just replaced the ignition module chip in the distributer cap turned it over and flames blew out of the carburator.(I think I'm getting spark now..lol but it


Try changing the fuel filter ... Chevrolet S 10

Thought the fuel pump was bad, engine died but after hitting tank with mallet it started up and ran. replace fuel filter. started and ran a few min then died wouldnt start up. replace fuel relay still wont start. there is spark at the plugs. and it starts with starting fluid in the TBI. cant hear the fuel pump run at this time


If you hit the tank and it ran? The fuel pump is bad. By striking the tank you jarred the pump, causing what mechanics call "The last ride" Peice of sound advise, Replace with ac delco pump. The zone pumps go out usaly within months if not days ... 1995 GMC Yukon

I have a 2000 ford f800 with a 5.9 cummins diesel engine it starts up and surges then dies and thats all it will do i also have no pedal response, i have tried a new injection pump and pickup pump,and also changed the engine speed sensor and crank sensor i still have the same problem , any suggestions? I have the same problem with a 1999 ford f 800 with a cummins isb 5.9 vp pump replaced & electric pump replaced just surges and dies. fuel pressure 14 psi


14psi sounds low even for the sump. ... 1999 Dodge Ram
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.2998 seconds