Having problems with your 1987 Chevrolet Blazer ?

Locking hub wont install on driver side of a 1987 chevy k5 blazer 1/2 ton, i can put it in but cant get retaining rings in. how do i do this?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 1987 Chevrolet Blazer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Locking hub wont install on driver side of a 1987 chevy k5 blazer 1/2 ton, i can put it in but cant get retaining rings in. how do i do this?


... 1987 Chevrolet Blazer

I tighten up the tilt colomn on a 89 chevy truck, got it all back together execpt the lock plate. cant get the plate to go down further enough to put the retainer ring on. please help.


Cut yourself a piece of wood, like a broomstick, about 16 inches long and place it against the lock plate. Put your shoulder against the other end and you should be able to push the plate down and still have your hands free to put the retainer clip o ... 1989 Chevrolet Suburban

Do i have to remove my clutch sensor to install my new push rod that connects the clutch pedal what happened is my clip broke that connects the clutch pedal to the rod i have the new push rod and clip because they come as one i tried to put the new clip on the old push rod but i cant seem to be able to get my hand up there well enough to get it to snap on so i figured i would pull the rod out snap the clip on and put it back in what should i do and or how do i put it in


What you might have to do is put the seat as far back as possible and put a blanket or something you can lay on,on your back facing up to the pedal.Use a light so you can see the area where you are installing the clip.As long as you have the new clip ... 2003 Pontiac Grand Am

Hi. my battery went flat and i recharged it but when i put it back in stupid put it in wrong way and it blew the alternator fuse which i have now replaced. this car is fitted with an immobilizer and normally i put the key in turn to accessories push the immobilizer button on the key ring and all the dash lights would come on and then it could be started but now am only getting to the push button on the key ring stage the dash lights arent coming on and i cant start the car...i think it's somethi


You need a professonal machanic!!!! ... Hyundai Excel

Put new pads on my 05 ford excursion 4x4 and I cant get the caliper to go back on the rotor. there are 3 pcs involved, the rotor, the caliper, and a bracket that the caliper mounts to. first I put on the rotor and then the bracket then the pads then the caliper. that did not work so I then put the pads in the caliper then attached the caliper to the bracket and then tried to install the whole assembly onto the rotor and that does not work either. Please help


Youll have to clamp the brake hose,undo the bleed screw,and push the piston[s] back in,then shut off bleed screw,undo clamp on hose,and try assembly again.bracket first,then pads into bracket,then slide caliper over pads,and then put bolts holding ca ... 2005 Ford Excursion

02 chevy blazer 4x4 136000 miles on it. Sluggish when accelerating. before i couldnt get it past 60 miles an hr without causing noises from the engine. now all of a sudden i cant even go more than 30 mph. Checked all fluids they are filled. Put seafoam in the gastank to take out any water. This is my only vehicle and I need to get it fixed any help is appreciated


I would check out the exhaust converter\015\012\015\012It should last 12 years or a lot longer\015\012\015\012When your vehicle does not run correctly and\015\012does so for years,it over heats the converter\015\01 ... 2002 Chevrolet Blazer

I installed HID headlights and fog lights about 2 months ago and the passanger side went out. i took the drivers side bulb and put it into the passanger side to see if the bulb or the ballast was bad and it didnt work either. so i figured it was the ballast. i then put it back on the drivers side and it wont work. i found that the passanger side was out bacause of a blown fuse and is now fixed and working. problem is i stilll cant get anything on the drivers side to work. i got a new HID kit and


... 2007 Chevrolet TrailBlazer SS

Starter instalation put in different starter, but cant remember what wires go where . where can i get a free diagram and instructions to print online so that i can get my car running...1994 chevy lumina euro 3.1L car..


You should only have 3 wires going to the starter there will be a large black wire possably with a red end, a thiner red wire and a thinner purple wire \015\012\015\012the thin purple wire is the trigger wire and goes on the small post on ... 1994 Chevrolet Lumina

I have a1995 ford windstar that i cant get the lower pressure hoses back on. so does it have an o ring that goes on as well? this is the old hose that is being put back on cause i had to replace the h


The end of the hose on the threads are damaged and you won't ever get it started ,get a new hose assy and check inside the pump fitting to make sure its not damaged also.if not than the hose will work if not change both of them ... 1995 Ford Windstar

Engine Install Trying to put on the brackets on a 350 engine just rebuilt for my 1983 Chevy Blazer. Any idea's on how to get pictures of the power steering pump, a/c compressor and the alternator.


Try on line internet look for diagram for a 1983 chevy blazer 350 engine.or go buy dealership see if they have engine diagram. ... 1983 Chevrolet Blazer

1984 gmc 1 ton 454 bigblock installed new. Carb ran great. Fired her up let her warm up while driving she just died and will not fire. Put new 8mm wires and plugs still no fire she is getting plenty of fuel but no spark. Any ideas?


Have you checked the coil? Sounds like issue with no fire/electrical spark getting to coil. ... Cars & Trucks

I have a 1997 blazer 4door had a new fuel pump & filter put in it now it gets hot shuts off & u cant hear the pump come on after 20 min it will start up & run fine thank you for your time


Take mass air flow sensor off and clean it with a non-chlronated brake cleaner let it dry for 30 minutes then reinstall.. ... 1997 Chevrolet Blazer

I have a 1993 chevy 1/2 ton pickup with 5.7 liter and I cant get the four wheel drive to work when i put it into four whell the rear wheels alternate when slipping as they should but nothing from the front wheels.


First of all try checking your fuse box and make sure the 4X4 fuse is\015\012still good. If the fuse is good, move the shift lever for the 4X4 on\015\012the floor into 4 high, then get a friend to watch underneath when you\015\012move the vehicle a l ... 1993 Chevrolet K1500

My car i have a 1998 chrysler sebring convertible and the back window broke i finally found a window to put in it but im not sure whom i should have to install it that wouldnt cost me a ton of money i would do it myself but i have know clue how.. it took me three months to get a window please help me


Do you have full glass coverage on your insurance? If so, they will pay to have it installed by any installer of your choice. There usually isn't a deductible for it.If not, call around. Make sure they know that you already have the windo ... 1998 Chrysler Sebring

I need to put brakes in my 1995 Chevy picku 4x4. I need a manual and cant afford 40 bucks for it. How can I get directions to remove and install new brakes on all 4 wheels?


Er,\015\012Go to the "Reference section" of your public library and locate either the Chilton's or the Motor's manual fro your pickup. Don't need a library card. Photocopy the pages you need using the public copy machines there. The manuals ... 1999 Chevrolet Silverado 1500

I have a 75 vw kommbi bus 1800cc I rebuilt the upper end of the motor new h/c heads new rings honed the bore all std . I put a new kit through the both the pdsit 34 carby's the kombi [is an auto ] befor the re build it got about 24mpg and could get up to 120ks . now it can still pull th120 but fuel consumption is now 15mpg as I hope to do some long distant travel I cant afford to run it I have balanced the carbies double checed timing and checked for vacuum leaks . the transmission has been che


Things to also check are the vacuum advance and centrifugal advance in the distributor. See that the vacuum unit is not leaking. Use a timing light and **** on the advance tube to see that it is funtioning(the timing wil change when sucking on the tu ... Volkswagen Camper

How do you put the valve cover gasket seals in properly???we have the the pink gasket and the 8 o-rings we're not sure what order they get installed in???


... 2009 Chrysler Town and Country

What tool do i use to put the little ring back on the steeringwheel shaft i cant push the spring down far enough to get it in the groove on the splined shaft this is on a 91 gmc s15 jimmy


Actually if you use a hard rubber mallet, you can get away from using any special tools. Using a flat-tip, common screwdriver, you can push and manipulate that clip back in. Use the mallet to seat the steering wheel as much as possible. ... 1990 GMC S-15 Jimmy

I cant get the retaining ring on the headlight bulb to turn so i can replace the head light. its a 1995 honda accord.


Spray VERY lightly some WD-40 around the bulb where the ring is holding it down. Wait about 2 minutes. Wiggle the ring by hand. If it still doesn't come loose, use a flat screwdriver on the edge ridges of the ring. Bump (hard) the screwdriver with t ... 1995 Honda Accord

Just replaced radiator in 2003 blazer old radiator leaked all fluid out put new fluid in to get home do i need to flush and fill or just fill ok do i need to jack up above heater coil to fill and does the v6 have a bleeder valve cant find one


Flush & fill is best -just fill is ok,you can fill it through the over-flow tank,(may take a while ) or remove the radiator cap & fill there ... 2003 Chevrolet Blazer

My blazer just turned off on me yesterday. I thought it was mabe not enough fuel but after i refueled it it only started once and shut back off. now i cant get it started for nothing iv put gas and treatment in the tank. it still wont start. any ideas as to what it could be . the key turns and the engine sounds like it wants to start. iv tryed starting it up so many times that the battery is dying had to jump it a few times.


Run fault codes check as it may be a failed cam/crank position sensor that will not allow it to start or some other faulty sensor that is the problem. Do not waste money until you know what you have to replace ... 1995 Chevrolet Blazer

2000 c2500 retaining clip on brake light switch broke off. Got the new clip, can't figure out how to get to it to install. Please don't tell me I have to remove the entire steering column to put on one lousy little clip?


... 1999 Chevrolet C2500

I am wondering if it is possible to remove, and re-install the clutch fork without taking out the transmission. I put the throw out bearing in the wrong way, I put it in the clips on the fork and it is supposed to just ride in the center portion of the bearing, and I am trying to get it outand leave the bearing straddling the shaft and install it correctly, because after replacing the transmission I cannot get it into any gear and that is the only thing that was done wrong, thanks for the help


Sorry but i have tried to change the folks a few times and have never been able to ... 1995 Chevrolet Camaro

Heater problem My 1999 blazer does not give much heat. If I put the selector switch to the A/C mode and put the temp dial to hot I then get alot more heat. But when I use the heat settings the correct way I don't get much heat and it does not seem to blow out as much air as it used to. The heater core is not plugged at all. I am thinking this has something to do with the flaps or something not working correctly under the dash. Any help with this would be greatly appeciated. Yep, my 02 Blazer he


I had one of these at my shop recently and I fixed it by replacing the heater control panel. I went for the resistor first with a known good one and it didn't take care of it. I bought a new heater control panel and that took care of the problem. ... 2002 Chevrolet Blazer

I'm getting the engine light coming every so often. It seems that after I fill the tank and get down around 3/4 tank, The message I'm getting is "EVAP Emission Control System Purge Flow Fault". PO441 and PO344 came up at the same time. I put a new camshaft sensor switch, new spark plugs, new wires on and put more grease on the gas cap o ring and treads. I reset the codes and drive about 5 miles and the PO344 comes on again. I took the - battery cable loose and put on another camshaft switch. I p


I have a 2004 dodge stratus 2.4 dual overhead cam. When driving down the road, bell goes off, check engine light comes on, and it's like I'm driving on limp mode, when going over 2000 rpm's, there's a severe stutter. After getting code for light it p ... 2004 Dodge Stratus
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.0714 seconds